RT9167A-30GB Richtek USA Inc, RT9167A-30GB Datasheet - Page 9

• Manufacturer Part Number: RT9167A-30GB
• Description: IC REG LDO 3.0V 500MA SOT23-5
• Manufacturer: Richtek USA Inc

Specifications of RT9167A-30GB

• Regulator Topology: Positive Fixed
• Voltage - Output: 3V
• Voltage - Input: Up to 7V
• Voltage - Dropout (typical): 0.6V @ 500mA
• Number Of Regulators: 1
• Current - Output: 500mA (Min)
• Current - Limit (min): 500mA
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: SC-74A, SOT-753
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Load-Transient Considerations
The RT9167/A load-transient response graphs (see Typical
Operating Characteristics) show two components of the
output response: a DC shift from the output impedance
due to the load current change, and the transient response.
The DC shift is quite small due to the excellent load
regulation of the IC. Typical output voltage transient spike
for a step change in the load current from 0mA to 50mA is
tens mV, depending on the ESR of the output capacitor.
Increasing the output capacitor's value and decreasing the
ESR attenuates the overshoot.
Shutdown Input Operation
The RT9167/A is shutdown by
and turned on by driving the input high. If this feature is
not to be used, the EN input should be tied to VIN to keep
the regulator on at all times (the EN input must not be left
floating).
To ensure proper operation, the signal source used to
drive the EN input must be able to swing above and below
the specified turn-on/turn-off voltage thresholds which
guarantee an ON or OFF state (see Electrical
Characteristics). The ON/OFF signal may come from
either CMOS output, or an open-collector output with pull-
up resistor to the RT9167/A input voltage or another logic
supply. The high-level voltage may exceed the
RT9167/A input voltage, but must remain within the
absolute maximum ratings for the EN pin.
Internal P-Channel Pass Transistor
The RT9167/A features a typical 1.1Ω P-MOSFET pass
transistor. It provides several advantages over similar
designs using PNP pass transistors, including longer
battery life. The P-MOSFET requires no base drive, which
reduces quiescent current considerably. PNP-based
regulators waste considerable current in dropout when the
pass transistor saturates. They also use high base-drive
currents under large loads. The RT9167/A does not suffer
from these problems and consume only 80μA of quiescent
current whether in dropout, light-load, or heavy-load
applications.
DS9167/A-28
September 2010
pulling the EN input low,
Input-Output (Dropout) Voltage
A regulator's minimum input-output voltage differential
(or dropout voltage) determines the lowest usable supply
voltage. In battery-powered systems, this will determine
the useful end-of-life battery voltage. Because the RT9167/
A uses a P-Channel MOSFET pass transistor, the dropout
voltage is a function of drain-to-source on-resistance
[R
Reverse Current Path
The power transistor used in the RT9167/A has an inherent
diode connected between the regulator input and output
(see Figure 3). If the output is forced above the input by
more than a diode-drop, this diode will become forward
biased and current will flow from the V
This diode will also be turned on by abruptly stepping the
input voltage to a value below the output voltage. To prevent
regulator mis-operation, a Schottky diode should be used
in any applications where input/output voltage conditions
can cause the internal diode to be turned on (see Figure4).
As shown, the Schottky diode is connected in parallel
with the internal parasitic diode and prevents it from being
turned on by limiting the voltage drop across it to about
0.3V. < 100mA to prevent damage to the part.
DS(ON)
VIN
] multiplied by the load current.
VIN
Figure 3
Figure 4
RT9167/A
OUT
www.richtek.com
terminal to V
VOUT
VOUT
IN
9
.