RPER71H103K2M1A03A Murata, RPER71H103K2M1A03A Datasheet - Page 17

• Manufacturer Part Number: RPER71H103K2M1A03A
• Description: Multilayer Ceramic Capacitors (MLCC) - Leaded 0.01uF 50volts X7R 10% 5.0mm L/S
• Manufacturer: Murata
• Series: RPEr

Specifications of RPER71H103K2M1A03A

• Voltage Rating: 50 Volts
• Termination Style: Radial
• Operating Temperature Range: - 55 C to + 125 C
• Product: General Type MLCCs
• Dimensions: 3.5 mm W x 5 mm L
• Capacitance: 0.01 uF
• Tolerance: 10 %
• Temperature Coefficient: X7R
• Lead Spacing: 5 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

1
!Note
!Note
16
No.
10
11
12 Solderability of Leads
13
14
Specifications and Test Methods
Continued from the preceding page.
Terminal
Strength
Vibration
Resistance
Resistance
to
Soldering
Heat
Temperature
and
Immersion
Cycle
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specifications before ordering.
Item
Tensile
Strength
Bending
Strength
Appearance
Capacitance
Q/D.F.
Appearance No defects or abnormalities
Capacitance
Change
Dielectric
Strength
(Between
Terminals)
Appearance No defects or abnormalities
Capacitance
Change
Q/D.F.
Insulation
Resistance
Dielectric
Strength
(Between
Terminals)
Temperature Compensating Type High Dielectric Constant Type
Termination not to be broken or loosened
Termination not to be broken or loosened
No defects or abnormalities
Within the specified tolerance
30pF min. : Q U 1000
30pF max. : Q U 400+20C
C : Nominal capacitance (pF)
Solder is deposited on unintermittently immersed portion in axial
direction covering 3/4 or more in circumferential direction of lead
wires.
Within T2.5% or T0.25pF
(whichever is larger)
No defects
Within T5% or T0.5pF
(whichever is larger)
30pF min. : Q U 350
10pF to 30pF : Q U 275+
10pF max. : Q U 200+10C
C : Nominal capacitance (pF)
10000MΩ or 500Ω • F min.
(whichever is smaller)
No defects or abnormalities
Specifications
5
2
C
Char. X7R
Char. Z5U
Char. Y5V : 0.05 max.
Char. X7R : Within T7.5%
Char. Z5U
Char. Y5V
Char. X7R : Within T12.5%
Char. Z5U
Char. Y5V
Char. X7R : 0.05 max.
Char. Z5U
Char. Y5V
Char. X7R : 10000MΩ or 500Ω • F min.
Char. Z5U
Char. Y5V
}
(whichever is smaller)
:
}
}
}
}
1000MΩ or 50Ω • F min.
(whichever is smaller)
: 0.025 max.
: Within T20%
: Within T30%
: 0.075 max.
As in the figure, fix the capacitor body, apply the force
gradually to each lead in the radial direction of the
capacitor until reaching 10N* and then keep the force
applied for 10T1 sec.
Each lead wire should be subjected to a force of 2.5N
and then bent 90˚ at the point of egress in one
direction. Each wire is then returned to the original
position and bent 90˚ in the opposite direction at the
rate of one bend per 2 to 3 sec.
The capacitor is soldered securely to a supporting
terminal and a 10 to 55Hz vibration of 1.5mm peak-
peak amplitude is applied for 6 hrs. total, 2 hrs. in each
mutually perpendicular direction. Allow 1 min. to cycle
the frequency from 10Hz to 55Hz and the converse.
The terminal of a capacitor is dipped into a 25%
ethanol (JIS-K-8101) solution of rosin (JIS-K-5902) and
then into molten solder (JIS-H-4341, H63A) of 235T5˚C
for 2T0.5 sec. In both cases the depth of dipping is up
to about 1.5mm to 2mm from the terminal body.
The lead wire is immersed in the melted solder (JIS-H-
4341, H63A) 1.5mm to 2mm from the main body at
270T5˚C for 3T0.5 sec. (L3.5 x W3.0 (mm) type) or
350T10˚C for 3.5T0.5 sec. (all other types). The
specified items are measured after 24T2 hrs.
(temperature compensating type) or 48T4 hrs. (high
dielectric type).
• Initial measurement for high dielectric constant type
The capacitors are heat treated for 1 hr. at 150
allowed to set at room temperature for 48T4 hrs., and
given an initial measurement.
First, repeat the following temperature/time cycle 5
times :
lowest operating temperature T3˚C/30T3 min.
Next, repeat twice the successive cycles of immersion,
each cycle consisting of immersion in a fresh water at
65
aqueous solution of salt at 0T3˚C for 15 min.
The capacitor is then promptly washed in running
water, dried with a drying cloth, and allowed to sit at
room temperature for 24T2 hrs. (temperature
compensating type) or 48T4 hrs. (high dielectric type).
• Initial measurement for high dielectric constant type
The capacitors are heat treated for 1 hr. at
150
T4 hrs., and given an initial measurement.
W5
Y0
ordinary temperature/3 min. max.
highest operating temperature T3˚C/30T3 min.
ordinary temperature/3 min. max.
W 0
Y10
˚C for 15 min. and immersion in a saturated
˚C, allowed to sit at room temperature for 48
F
Test Method
Continued on the following page.
* 5N for L3.5 x W3.0 (mm)
C49E15.pdf 04.12.29
W 0
Y10
˚C,