011796 AP (SAK4/6) Weidmuller, 011796 AP (SAK4/6) Datasheet - Page 15

• Manufacturer Part Number: 011796 AP (SAK4/6)
• Description: END COVER, BUFF
• Manufacturer: Weidmuller
• Series: Wr

Specifications of 011796 AP (SAK4/6)

• Svhc: No SVHC (15-Dec-2010)
• Colour: Buff
• External Length / Height: 51.5mm
• Accessory Type: End / Intermediate Plate
• For Use With: W Series
• Lead Free Status / RoHS Status: na

This series has versions for conductors
up to 150 mm
• Only two different end plates.
• The larger end plate can be used as a
• Both end plates latch tightly onto the
Because of its clearly reduced external
dimensions, the WDU 1.5 is particularly
suitable for confined spaces. This small
design does, however, make parallel
cross-connection impossible and a sepa-
rate end plate is needed.
Assembly and removal
The terminals can be moved along the
mounting rail with little effort. This is
advantageous because it allows the posi-
tion of a terminal strip to be easily mat-
ched to local conditions.
End brackets fitted on the left and right
prevent undesired displacement and
securely position the terminals.
End brackets can also accept marking
tags and thus be used for group marking.
latch on
partition for the smaller terminals.
terminals.
W
2
.
latch off
The new cross-connection system
offers particular advantages.
• Pre-assembled units with 2, 3, 4 and
• Shock-hazard protection according to
• Captive fixing screws. Screwdriver gui-
• Engageable in terminal moulding
• No end plates or partitions for neigh-
• The full terminal rated current can be
• Snap-off connection tags - skipping of
• Offset arrangement in terminal moulding
Combination
Feed-through terminals
for L1, N disconnect
and PE terminals
This cross-connection system cannot
only be employed with feed-through ter-
minals, but also in combination with PE
terminals and N-disconnect terminals.
Extremely economical terminal strips can
be assembled in this way.
Although each individual terminal block is
shock-hazard protected with and with-
out cross-connection, covers with high
voltage flash DIN 30600 can be snap-fit-
ted for all terminals up to 150 mm
cross-section; a group tag carrier can
also be fitted as an alternative.
• Marking of live terminals.
• Absolute shock protection is guaran-
• Practical identification of functional
• Three systems available for terminal
10 poles.
VBG 4 or. VDE 0106 Part 100/3.83
without additional components.
dance through countersunk arrange-
ment.
– simple overhead assembly.
bouring cross-connection up to 400V.
fed across all numbers of poles.
terminals is possible.
– parallel use of 2 potentials possible
teed.
groups in addition to terminal marking.
marking - up to 10 characters possible.
Simple
Arrangement of
2 potentials
Parallel
2
rated
Weidmüller double deck terminals permit
high wiring density despite their narrow
width. The number of terminal points can
be doubled by exchanging for 5 mm-wide
standard terminals, without lengthening the
mounting rail.
Weidmüller double deck terminals have
the following wiring advantages:
• Cross-connections possible in one or
• Current bar connection between upper
• Individual terminals replaceable without
• Clear identification of individual termi-
• For potential multiplication in confined
An additional feature is the letter V in the
type designation, such as
– WDK 2.5 V
both levels.
and lower level optional.
moving neighbouring terminals
nals
spaces we recommend, for example,
Weidmüller double deck terminals with
current bar connection between the
upper and lower levels.
These terminals can be recognised by
the V-shaped groove in the terminal
moulding.
Cat.No. 102230
2/3
2