RYC9906 Tyco Electronics, RYC9906 Datasheet
RYC9906
Specifications of RYC9906
Related parts for RYC9906
RYC9906 Summary of contents
Page 1
... RYC9906 High Power LED Boost GENERAL DESCRIPTION The RYC9906 device is a low-cost integrated boost converter IC specifically designed for driving high power LEDs. It can be operated from a single Lithium cell or two alkaline cells, and drives LEDs. The RYC9906 device regulates at constant current, yielding constant illumination over input voltage ...
Page 2
... RYC9906 High Power LED Boost ORDERING INFORMATION Part Part Description Number RYC9906 A39770-000 MATERIAL INFORMATION ROHS Compliant PIN CONFIGURATION PGND 7 2 GND PIN DESCRIPTION Pin Number Pin Name Pin Function 1 Connect. 2 PGND Power Ground. 3 GND Ground. Feedback. This pin is the feedback to the PWM to control the output current. Attach to ...
Page 3
... RYC9906 High Power LED Boost ABSOLUTE MAXIMUM RATINGS Parameter VCC to GND Lx to GND All Other Pins to GND Continuous Power Dissipation (70°C) (Derate 8.7mW/°C above 70°C) Ambient operating temperature Storage temperature Max lead temperature during soldering (5 sec.) Note 1. Operation beyond absolute maximum rating or improper use may result in permanent damage to the device. ...
Page 4
... RYC9906 High Power LED Boost TYPICAL CHARACTERISTICS Switching Waveforms, Pout = 1W LX 10V/Div IL 1A/Div 5 sec/Div LED Current vs. Modulation PWM = 1KHz 5 0 Duty Cycle (%) Tyco Electronics Corporation 308 Constitution Drive, Menlo Park, CA 94025 Tel: (800) 227-4856 Fax: (800) 227-4866 © 2005 Tyco Electronics Corporation. ...
Page 5
... RYC9906 High Power LED Boost TYPICAL CHARACTERISTICS (CONT) Frequency Normalized at 25°C 1.2 1.15 1.1 1.05 1 0.95 0.9 0.85 0 Junction Temperature (ºC) Supply Current Normalized at 25°C 1.4 1.3 1.2 1.1 1 0.9 0.8 0.7 0.6 -55 -35 - Junction Temperature (ºC) Tyco Electronics Corporation 308 Constitution Drive, Menlo Park, CA 94025 Tel: (800) 227-4856 Fax: (800) 227-4866 © ...
Page 6
... Any L1 Raychem U1 RYC9906 Tyco Electronics Corporation 308 Constitution Drive, Menlo Park, CA 94025 Tel: (800) 227-4856 Fax: (800) 227-4866 © 2005 Tyco Electronics Corporation ENABLE 2 RYC9906 Quantity Description 1 10µF, 6.3V Aluminum Electrolytic Cap 1 100µF, 6.3V Aluminum Electrolytic Cap 1 1A, 30V Schottky ...
Page 7
... SO-8 package Startup The RYC9906 device does not require a soft-start. It has a current limit on the LX pin that is designed to avoid damage to the IC even by a short circuit. At startup, then, it simply runs at maximum current until the output capacitor is charged, at which time it enters normal operation ...
Page 8
... Vin VCC Figure 2. Bootstrapping Circuit Enable The RYC9906 device can be turned off by pulling the ENABLE pin high. In this condition, there is extremely low leakage current into the IC, and relatively low current into the LED, since the supply voltage (minus a diode drop) is less than the forward voltage required to turn on the LED ...
Page 9
... Operation with a High or Low Input Voltage If the power source available is outside the recommended operating range of the IC, the RYC9906 device can still be use to drive LEDs this, the power source may be connected to the inductor, while the VCC pin needs to receive a small amount of current within its operating range. ...
Page 10
... RYC9906 High Power LED Boost PACKAGE INFORMATION SO-8 PACKAGE NOTES: 1. Dimensions and tolerance per ANSI Y14.5M-1982. 2. Dimensions A and B are datums and datum surface. 3. Controlling dimensions: Millimeters 4. Dimension A and B do not include mold flash. Mold flash shall not exceed 0.15mm [0.006] per side. ...
Page 11
... RYC9906 High Power LED Boost Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of each product for their applications. Tyco Electronics Corporation assumes no responsibility for the use of its product or for any infringement of patents or other rights of third parties resulting from the use of its product. No license is granted by implication or otherwise under any patent or proprietary right of Tyco Electronics except the right to use such product for the purpose for which it is sold. Tyco Electronics reserves the right to change or update, without notice, any information contained in this publication ...