DSPIC33FJ128GP802-E/MM Microchip Technology, DSPIC33FJ128GP802-E/MM Datasheet - Page 160

• Manufacturer Part Number: DSPIC33FJ128GP802-E/MM
• Description: IC, DSC, 16BIT, 128KB 40MHZ, 3.6V, QFN28
• Manufacturer: Microchip Technology
• Series: DsPIC33Fr

Specifications of DSPIC33FJ128GP802-E/MM

• Core Frequency: 40MHz
• Core Supply Voltage: 3.6V
• No. Of I/o's: 21
• Flash Memory Size: 128KB
• Supply Voltage Range: 3V To 3.6V
• Operating Temperature Range: -40°C To +125°C
• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: AC'97, Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 21
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 10x10b/12b, D/A 4x16b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 28-QFN
• Rohs Compliant: Yes
• Package: 28QFN-S EP
• Device Core: dsPIC
• Family Name: dSPIC33
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 21
• Interface Type: CAN/I2C/SPI/UART
• On-chip Adc: 10-chx10-bit|10-chx12-bit
• On-chip Dac: 2-chx16-bit
• Number Of Timers: 5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DV164033 - KIT START EXPLORER 16 MPLAB ICD2DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

dsPIC33FJ32GP302/304, dsPIC33FJ64GPX02/X04, AND dsPIC33FJ128GPX02/X04
11.2
In addition to the PORT, LAT and TRIS registers for
data control, some port pins can also be individually
configured for either digital or open-drain output. This
is controlled by the Open-Drain Control register,
ODCx, associated with each port. Setting any of the
bits configures the corresponding pin to act as an
open-drain output.
The open-drain feature allows the generation of
outputs higher than V
tolerant pins by using external pull-up resistors. The
maximum open-drain voltage allowed is the same as
the maximum V
Refer to “Pin Diagrams” for the available pins and
their functionality.
11.3
The AD1PCFGL and TRIS registers control the opera-
tion of the analog-to-digital (A/D) port pins. The port
pins that are to function as analog inputs must have
their corresponding TRIS bit set (input). If the TRIS bit
is cleared (output), the digital output level (V
is converted.
The AD1PCFGL register has a default value of 0x0000;
therefore, all pins that share ANx functions are analog
(not digital) by default.
When the PORT register is read, all pins configured as
analog input channels are read as cleared (a low level).
Pins configured as digital inputs do not convert an
analog input. Analog levels on any pin defined as a
digital input (including the ANx pins) can cause the
input buffer to consume current that exceeds the
device specifications.
EXAMPLE 11-1:
DS70292D-page 160
MOV
MOV
NOP
btss
0xFF00, W0
W0, TRISBB
PORTB, #13
Open-Drain Configuration
Configuring Analog Port Pins
IH
specification.
DD
PORT WRITE/READ EXAMPLE
(e.g., 5V) on any desired 5V
; Configure PORTB<15:8> as inputs
; and PORTB<7:0> as outputs
; Delay 1 cycle
; Next Instruction
OH
or V
Preliminary
OL
)
11.4
One instruction cycle is required between a port
direction change or port write operation and a read
operation of the same port. Typically this instruction
would be an NOP, as shown in Example 11-1.
11.5
The input change notification function of the I/O ports
allows
dsPIC33FJ64GPX02/X04, and dsPIC33FJ128GPX02/
X04 devices to generate interrupt requests to the pro-
cessor in response to a change-of-state on selected
input pins. This feature can detect input change-of-
states even in Sleep mode, when the clocks are dis-
abled. Depending on the device pin count, up to 21
external signals (CNx pin) can be selected (enabled)
for generating an interrupt request on a change-of-
state.
Four control registers are associated with the CN mod-
ule. The CNEN1 and CNEN2 registers contain the
interrupt enable control bits for each of the CN input
pins. Setting any of these bits enables a CN interrupt
for the corresponding pins.
Each CN pin also has a weak pull-up connected to it.
The pull-ups act as a current source connected to the
pin, and eliminate the need for external resistors when
push-button or keypad devices are connected. The
pull-ups are enabled separately using the CNPU1 and
CNPU2 registers, which contain the control bits for
each of the CN pins. Setting any of the control bits
enables the weak pull-ups for the corresponding pins.
Note:
I/O Port Write/Read Timing
Input Change Notification
Pull-ups on change notification pins
should always be disabled when the port
pin is configured as a digital output.
the
 2009 Microchip Technology Inc.
dsPIC33FJ32GP302/304,