ADP150ACBZ-3.3-R7 Analog Devices Inc, ADP150ACBZ-3.3-R7 Datasheet - Page 4

• Manufacturer Part Number: ADP150ACBZ-3.3-R7
• Description: IC, LDO VOLT REG, 3.3V, 150mA, WLCSP-4
• Manufacturer: Analog Devices Inc

Specifications of ADP150ACBZ-3.3-R7

• Primary Input Voltage: 5.5V
• Output Voltage Fixed: 3.3V
• Dropout Voltage Vdo: 105mV
• No. Of Pins: 4
• Output Current: 150mA
• Operating Temperature Range: -40°C To +125°C
• Msl: MSL 1 - Unlimited
• Design Resources: Broadband Low EVM Direct Conversion Transmitter (CN0134) Broadband Low EVM Direct Conversion Transmitter Using LO Divide-by-2 Modulator (CN0144) Using low noise linear drop-out regulators to power wideband PLL & VCO IC's (CN0147)
• Regulator Topology: Positive Fixed
• Voltage - Output: 3.3V
• Voltage - Input: Up to 5.5V
• Voltage - Dropout (typical): 0.105V @ 150mA
• Number Of Regulators: 1
• Current - Output: 150mA (Max)
• Current - Limit (min): 190mA
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 4-WLCSP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ADP150ACBZ-3.3-R7TR

ADP150
Parameter
POWER SUPPLY REJECTION RATIO
POWER SUPPLY REJECTION RATIO
1
2
3
4
RECOMMENDED SPECIFICATIONS: INPUT AND OUTPUT CAPACITOR
Table 2.
Parameter
INPUT AND OUTPUT CAPACITOR
1
voltages above 2.2 V.
output voltage is defined as the current that causes the output voltage to drop to 90% of 3.0 V or 2.7 V.
Based on an end-point calculation using 1 mA and 150 mA loads. See Figure 6 for typical load regulation performance for loads less than 1 mA.
Dropout voltage is defined as the input-to-output voltage differential when the input voltage is set to the nominal output voltage. This applies only for output
Start-up time is defined as the time between the rising edges of EN to V
Current limit threshold is defined as the current at which the output voltage drops to 90% of the specified typical value. For example, the current limit for a 3.0 V
The minimum input and output capacitance should be greater than 0.7 µF over the full range of operating conditions. The full range of operating conditions in the
application must be considered during device selection to ensure that the minimum capacitance specification is met. X7R-type and X5R-type capacitors are
recommended, and Y5V and Z5U capacitors are not recommended for use with any LDO.
(V
(V
Minimum Input and Output Capacitance
Capacitor ESR
IN
IN
= V
= V
OUT
OUT
+ 0.5 V)
+ 1 V)
Symbol
PSRR
1
Conditions
10 kHz, V
10 kHz, V
100 kHz, V
100 kHz, V
10 kHz, V
100 kHz, V
Symbol
C
R
ESR
MIN
OUT
IN
IN
IN
Rev. A | Page 4 of 20
IN
IN
IN
being at 90% of its nominal value.
= 3.8 V, V
= 2.3 V, V
= 4.3 V, V
= 3.8 V, V
= 2.3 V, V
= 4.3 V, V
OUT
OUT
OUT
Conditions
T
T
A
A
OUT
OUT
OUT
= −40°C to +125°C
= −40°C to +125°C
= 3.3 V, I
= 1.8 V, I
= 3.3 V, I
= 3.3 V, I
= 1.8 V, I
= 3.3 V, I
OUT
OUT
OUT
OUT
OUT
OUT
= 10 mA
= 10 mA
= 10 mA
= 10 mA
= 10 mA
= 10 mA
Min
0.7
0.001
Min
Typ
70
70
55
55
70
55
Typ
Max
Max
0.2
Unit
dB
dB
dB
dB
dB
dB
Unit
µF
Ω