LT1761IS5-2.5#PBF Linear Technology, LT1761IS5-2.5#PBF Datasheet - Page 6

• Manufacturer Part Number: LT1761IS5-2.5#PBF
• Description: IC, LDO VOLT REG, 2.5V, 0.1A, 5-TSOT-23
• Manufacturer: Linear Technology

Specifications of LT1761IS5-2.5#PBF

• Primary Input Voltage: 3.5V
• Output Voltage Fixed: 2.5V
• Dropout Voltage Vdo: 300mV
• No. Of Pins: 5
• Output Current: 100mA
• Operating Temperature Range: -40°C To +125°C
• Termination Type: SMD
• Msl: MSL 1 - Unlimited
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

LT1761 Series
ELECTRICAL CHARACTERISTICS
PARAMETER
GND Pin Current
V
(Notes 5, 7)
Output Voltage Noise
ADJ Pin Bias Current
Shutdown Threshold
SHDN Pin Current
(Note 9)
Quiescent Current in Shutdown
Ripple Rejection (Note 3)
Current Limit
Input Reverse Leakage Current
Reverse Output Current
(Note 10)
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LT1761 regulators are tested and specifi ed under pulse load
conditions such that T
at T
characterization and correlation with statistical process controls. The
LT1761I is guaranteed over the full –40°C to 125°C operating junction
temperature range. The LT1761MP is 100% tested and guaranteed over
the –55°C to 125°C operating junction temperature range.
Note 3: The LT1761 (adjustable versions) are tested and specifi ed for
these conditions with the ADJ pin connected to the OUT pin.
Note 4: Operating conditions are limited by maximum junction
temperature. The regulated output voltage specifi cation will not apply
for all possible combinations of input voltage and output current. When
operating at maximum input voltage, the output current range must be
limited. When operating at maximum output current, the input voltage
range must be limited.
Note 5: To satisfy requirements for minimum input voltage, the LT1761
(adjustable version) is tested and specifi ed for these conditions with an
external resistor divider (two 250k resistors) for an output voltage of
2.44V. The external resistor divider will add a 5μA DC load on the output.
6
temperature range, otherwise specifi cations are at T
IN
A
= V
= 25°C. Performance at –40°C and 125°C is assured by design,
OUT(NOMINAL)
J
≈ T
A
. The LT1761E is 100% production tested
CONDITIONS
I
I
I
I
I
C
(Notes 3, 8)
V
V
V
V
V
V
I
V
V
V
LT1761-1.2
LT1761-1.5
LT1761-1.8
LT1761-2
LT1761-2.5
LT1761-2.8
LT1761-3
LT1761-3.3
LT1761-5
LT1761 (Note 3)
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
OUT
OUT
OUT
SHDN
SHDN
IN
IN
IN
IN
IN
= 6V, V
– V
= 7V, V
= V
= –20V, V
= 10μF , C
= Off to On
= On to Off
= 0mA
= 1mA
= 10mA
= 50mA
= 100mA
= 50mA
= 0V
= 20V
OUT
OUT(NOMINAL)
SHDN
OUT
= 1.5V (Avg), V
OUT
BYP
= 0V
= 0V
= 0V
= 0.01μF , I
A
+ 1V or 2.3V (Note 12), ΔV
V
V
V
V
V
V
V
V
V
V
= 25°C. (Note 2)
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
RIPPLE
= 1.2V, V
= 1.5V, V
= 1.8V, V
= 2V, V
= 2.5V, V
= 2.8V, V
= 3V, V
= 3.3V, V
= 5V, V
= 1.22V, V
The
LOAD
l
= 0.5V
IN
IN
IN
= 100mA, BW = 10Hz to 100kHz
denotes the specifi cations which apply over the full operating
IN
IN
IN
IN
IN
IN
< 2V
< 3V
< 5V
IN
< 1.2V
< 1.5V
< 1.8V
< 2.5V
< 2.8V
< 3.3V
< 1.22V
Note 6: Dropout voltage is the minimum input to output voltage differential
needed to maintain regulation at a specifi ed output current. In dropout, the
output voltage will be equal to: V
Note 7: GND pin current is tested with V
(whichever is greater) and a current source load. This means the device
is tested while operating in its dropout region or at the minimum input
voltage specifi cation. This is the worst-case GND pin current. The GND pin
current will decrease slightly at higher input voltages.
Note 8: ADJ pin bias current fl ows into the ADJ pin.
Note 9: SHDN pin current fl ows into the SHDN pin.
Note 10: Reverse output current is tested with the IN pin grounded and the
OUT pin forced to the rated output voltage. This current fl ows into the OUT
pin and out the GND pin.
Note 11: For the LT1761, LT1761-1.2, LT1761-1.5, LT1761-1.8 and
LT1761-2 dropout voltage will be limited by the minimum input voltage
specifi cation under some output voltage/load conditions. See the curve of
Minimum Input Voltage in the Typical Performance Characteristics.
Note 12: To satisfy requirements for minimum input voltage, current limit
is tested at V
P-P
, f
RIPPLE
OUT
= 120Hz,
= –5%
IN
= V
OUT(NOMINAL)
l
l
l
l
l
l
l
l
l
l
l
+ 1V or V
IN
– V
0.25
MIN
110
55
DROPOUT
IN
IN
= V
= 2.3V, whichever is greater.
OUT(NOMINAL)
0.65
0.01
TYP
230
200
.
2.2
0.8
20
55
20
30
65
10
10
10
10
10
10
10
10
10
1
0
1
5
MAX
100
400
100
0.5
0.1
45
20
20
20
20
20
20
20
20
20
10
2
4
2
3
1
or V
IN
= 2.3V
μV
UNITS
1761sff
RMS
mA
mA
mA
mA
mA
μA
μA
μA
nA
μA
μA
μA
dB
μA
μA
μA
μA
μA
μA
μA
μA
μA
μA
V
V