MCP1827-3302E/ET Microchip Technology, MCP1827-3302E/ET Datasheet - Page 15

IC, LDO VOLT REG, 3.3V, 1.5A, D2-PAK-5

MCP1827-3302E/ET

Manufacturer Part Number
MCP1827-3302E/ET
Description
IC, LDO VOLT REG, 3.3V, 1.5A, D2-PAK-5
Manufacturer
Microchip Technology
Datasheet

Specifications of MCP1827-3302E/ET

Primary Input Voltage
3.9V
Output Voltage Fixed
3.3V
Dropout Voltage Vdo
330mV
No. Of Pins
5
Output Current
1.5A
Operating Temperature Range
-40°C To +125°C
Regulator Topology
Positive Fixed
Voltage - Output
3.3V
Voltage - Input
Up to 6V
Voltage - Dropout (typical)
0.33V @ 1.5A
Number Of Regulators
1
Current - Output
1.5A (Min)
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
TO-263-5, D²Pak (5 leads + Tab), TO-263BA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Limit (min)
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MCP1827-3302E/ET
Manufacturer:
MICROCHIP
Quantity:
12 000
3.0
The descriptions of the pins are listed in Table 3-1.
TABLE 3-1:
3.1
Connect the unregulated or regulated input voltage
source to V
several inches away from the LDO, or the input source
is a battery, it is recommended that an input capacitor
be used. A typical input capacitance value of 1 µF to
10 µF should be sufficient for most applications.
3.2
The SHDN input is used to turn the LDO output voltage
on and off. When the SHDN input is at a logic-high
level, the LDO output voltage is enabled. When the
SHDN input is pulled to a logic-low level, the LDO
output voltage is disabled. When the SHDN input is
pulled low, the PWRGD output also goes low and the
LDO enters a low quiescent current shutdown state
where the typical quiescent current is 0.1 µA.
3.3
Connect the GND pin of the LDO to a quiet circuit
ground. This will help the LDO power supply rejection
ratio and noise performance. The ground pin of the
LDO only conducts the quiescent current of the LDO
(typically 120 µA), so a heavy trace is not required.
For applications have switching or noisy inputs tie the
GND pin to the return of the output capacitor. Ground
planes help lower inductance and voltage spikes
caused by fast transient load currents and are
recommended for applications that are subjected to
fast load transients.
©
3-Pin Fixed
2007 Microchip Technology Inc.
Output
Pad
1
2
3
PIN DESCRIPTION
Input Voltage Supply (V
Shutdown Control Input (SHDN)
Ground (GND)
IN
. If the input voltage source is located
PIN FUNCTION TABLE
5-Pin Fixed
Output
Pad
1
2
3
4
5
Adjustable
Output
Pad
IN
1
2
3
4
5
)
PWRGD
SHDN
Name
V
GND
ADJ
V
EP
OUT
IN
MCP1827/MCP1827S
3.4
The PWRGD output is an open-drain output used to
indicate when the LDO output voltage is within 92%
(typically) of its nominal regulation value. The PWRGD
threshold has a typical hysteresis value of 2%. The
PWRGD output is delayed by 200 µs (typical) from the
time the LDO output is within 92% + 3% (max
hysteresis) of the regulated output value on power-up.
This delay time is internally fixed.
3.5
For adjustable applications, the output voltage is
connected to the ADJ input through a resistor divider
that sets the output voltage regulation value. This
provides the user the capability to set the output
voltage to any value they desire within the 0.8V to 5.0V
range of the device.
3.6
The V
LDO. A minimum output capacitance of 1.0 µF is
required for LDO stability. The MCP1827/MCP1827S is
stable with ceramic, tantalum and aluminum-electro-
lytic capacitors. See Section 4.3 “Output Capacitor”
for output capacitor selection guidance.
3.7
The DDPAK and TO-220 package have an exposed tab
on the package. A heat sink may be mount to the tab to
aid in the removal of heat from the package during
operation. The exposed tab is at the ground potential of
the LDO.
Description
Shutdown Control Input (active-low)
Input Voltage Supply
Ground
Regulated Output Voltage
Power Good Output
Voltage Adjust/Sense Input
Exposed Pad of the Package (ground potential)
OUT
Power Good Output (PWRGD)
Output Voltage Adjust Input (ADJ)
Regulated Output Voltage (V
Exposed Pad (EP)
pin is the regulated output voltage of the
DS22001C-page 15
OUT
)

Related parts for MCP1827-3302E/ET