DSPIC30F3013T-20E/ML Microchip Technology, DSPIC30F3013T-20E/ML Datasheet - Page 8

• Manufacturer Part Number: DSPIC30F3013T-20E/ML
• Description: IC,DSP,16-BIT,CMOS,LLCC,44PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F3013T-20E/ML

• Rohs Compliant: YES
• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 20 MIPS
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 20
• Program Memory Size: 24KB (8K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 44-QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DV164033 - KIT START EXPLORER 16 MPLAB ICD2DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

dsPIC30F3012/3013
6. Module: CPU
DS80448D-page 8
When a user executes a DISI #7, for example,
this will disable interrupts for 7 + 1 cycles (7 + the
DISI instruction itself). In this case, the DISI
instruction uses a counter which counts down from
7 to 0. The counter is loaded with 7 at the end of
the DISI instruction.
If the user code executes another DISI on the
instruction cycle where the DISI counter has
become zero, the new DISI count is loaded, but the
DISI state machine does not properly re-engage
and continue to disable interrupts. At this point, all
interrupts are enabled. The next time the user code
executes a DISI instruction, the feature will act
normally and block interrupts.
In summary, it is only when a DISI execution is
coincident with the current DISI count = 0, that the
issue occurs. Executing a DISI instruction before
the DISI counter reaches zero will not produce
this error. In this case, the DISI counter is loaded
with the new value, and interrupts remain disabled
until the counter becomes zero.
Work around
When executing multiple DISI instructions within
the source code, make sure that subsequent DISI
instructions have at least one instruction cycle
between the time that the DISI counter
decrements to zero and the next DISI instruction.
Alternatively, make sure that subsequent DISI
instructions are called before the DISI counter
decrements to zero.
Affected Silicon Revisions
B0
X
B1
X
7. Module: Output Compare
8. Module: Output Compare
If the desired duty cycle is ‘0’ (OCxRS = 0), the
module will generate a high level glitch of 1 T
The second problem is that on the next cycle after
the glitch, the OC pin does not go high, in other
words, it misses the next compare for any value
written on OCxRS.
Work around
There are two possible solutions to this problem:
1. Load a value greater than ‘0’ to the OCxRS
2. If the application requires 0% duty cycles, the
Affected Silicon Revisions
A glitch will be produced on an output compare pin
under the following conditions:
• The user software initially drives the I/O pin
• The output compare module is configured
When these events occur, the output compare
module will drive the pin low for one instruction
cycle (T
Work around
None. However, the user may use a timer interrupt
and write to the associated PORT register to
control the pin manually.
Affected Silicon Revisions
B0
B0
X
high using the output compare module or a
write to the associated PORT register.
and enabled to drive the pin low at some
point in later time (OCxCON = 0x0002 or
OCxCON = 0x0003).
X
register when operating in PWM mode. In this
case, no 0% duty cycle is achievable.
output compare module can be disabled
for 0% duty cycles, and re-enabled for
non-zero percent duty cycles.
CY
B1
B1
X
X
) after the module is enabled.
© 2010 Microchip Technology Inc.
CY
.