PIC24HJ64GP206T-I/PT Microchip Technology, PIC24HJ64GP206T-I/PT Datasheet - Page 65

• Manufacturer Part Number: PIC24HJ64GP206T-I/PT
• Description: Microcontroller
• Manufacturer: Microchip Technology
• Series: PIC® 24Hr

Specifications of PIC24HJ64GP206T-I/PT

• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 64KB (22K x 24)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 18x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM300024 - KIT DEMO DSPICDEM 1.1MA240012 - MODULE PLUG-IN PIC24H 100QFPDV164033 - KIT START EXPLORER 16 MPLAB ICD2DM300019 - BOARD DEMO DSPICDEM 80L STARTERDM240001 - BOARD DEMO PIC24/DSPIC33/PIC32AC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

6.0
The Reset module combines all Reset sources and
controls the device Master Reset Signal, SYSRST. The
following is a list of device Reset sources:
• POR: Power-on Reset
• BOR: Brown-out Reset
• MCLR: Master Clear Pin Reset
• SWR: RESET Instruction
• WDT: Watchdog Timer Reset
• TRAPR: Trap Conflict Reset
• IOPUWR: Illegal Opcode and Uninitialized W
A simplified block diagram of the Reset module is
shown in Figure 6-1.
FIGURE 6-1:
© 2009 Microchip Technology Inc.
Note:
Register Reset
RESET
This data sheet summarizes the features
of the PIC24HJXXXGPX06/X08/X10 fam-
ily of devices. However, it is not intended
to be a comprehensive reference source.
To complement the information in this data
sheet, refer to the “PIC24H Family Refer-
ence
(DS70229), which is available from the
Microchip website (www.microchip.com).
MCLR
V
Manual”,
DD
Uninitialized W Register
RESET SYSTEM BLOCK DIAGRAM
Regulator
RESET Instruction
Internal
Sleep or Idle
Module
Illegal Opcode
WDT
Trap Conflict
Section
V
8.
Detect
DD
Glitch Filter
PIC24HJXXXGPX06/X08/X10
Rise
“Reset”
BOR
POR
Any active source of Reset will make the SYSRST sig-
nal active. Many registers associated with the CPU and
peripherals are forced to a known Reset state. Most
registers are unaffected by a Reset; their status is
unknown on POR and unchanged by all other Resets.
All types of device Reset will set a corresponding status
bit in the RCON register to indicate the type of Reset
(see Register 6-1). A POR will clear all bits, except for
the POR bit (RCON<0>), that are set. The user can set
or clear any bit at any time during code execution. The
RCON bits only serve as status bits. Setting a particular
Reset status bit in software does not cause a device
Reset to occur.
The RCON register also has other bits associated with
the Watchdog Timer and device power-saving states.
The function of these bits is discussed in other sections
of this manual.
Note:
Note:
Refer to the specific peripheral or CPU
section of this manual for register Reset
states.
The status bits in the RCON register
should be cleared after they are read so
that the next RCON register value after a
device Reset will be meaningful.
SYSRST
DS70175H-page 63