HE1AN24 PANASONIC EW, HE1AN24 Datasheet - Page 5

• Manufacturer Part Number: HE1AN24
• Description: RELAY, SPNO, 24V
• Manufacturer: PANASONIC EW

Specifications of HE1AN24

• Relay Type: Power
• Coil Voltage Vdc Nom: 24V
• Contact Current Max: 30A
• Contact Voltage Ac Nom: 277V
• Contact Voltage Dc Nom: 30V
• Coil Resistance: 300ohm
• Coil Type: DC Coil
• Coil Current: 80mA
• Nom Operating Power: 1.92W
• Contact Configuration: SPNO
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

1 Form A Type
1. Maximum switching power
4. Ambient temperature characteristics
Sample: HE2aN-AC120V, 6 pcs.
MOUNTING METHOD
1. Plug-in terminal type
NOTES
1. The dust cover should not be removed
since doing so may alter the
characteristics.
2. Avoid use under severe environmental
conditions, such as high humidity,
organic gas or in dust, oily locations and
locations subjected to extremely frequent
shock or vibrations.
3. When mounting, use spring washers.
Optimum fastening torque ranges from 5
kg to 7 kg·cm
4. Firmly insert the receptacles so that
there is no slack or looseness. To remove
a receptacle, 2 to 4 kg of pulling strength
For Cautions for Use, see Relay Technical Information (see catalog).
en_ds_61120_0000: 310105J
M 4 screw
100
0.5
Washer
50
30
20
10
5
1
-50
DC resistive
4.5 to 6
-20
30
0
20
10
Contact voltage, V
100
pounds·inch.
20
-10
-20
-30
Pick-up
voltage
40
Faston No.250
AC resistive
60
Ambient
temperature, °C
Drop-out
voltage
500 1,000
80
x -
x -
2. Life curve
2. Screw terminal type
is required. Do not remove more than
one receptacle at one time.Always
remove one receptacle at a time and pull
it straight outwards.
5. Install the relay so that it lies in
direction A (up-down direction). (Pick-up
voltage and drop-out voltage values are
those when installed in direction A.)
6. When using the AC type, the operate
time due to the in-rush phase is 20 ms or
more. Therefore, it is necessary for you
to verify the characteristics for your actual
circuit. Moreover, the release time for the
NC side of the 2a1b type requires the
1,000
500
100
50
10
5
0
5
10
M 4 screw
Washer
15
250 V AC resistive
30 V DC resistive
Contact current, A
20
25
30
35
3. Contact temperature rise (DC type)
Measured portion: Inside the coil
Contact current: 30 A
3. Allowable installation wiring size for
screw terminal types and terminal blocks
Due to the UP terminals, it is possible to
either directly connect the wires or use
crimped terminal
same verification.
7. When using the push-on blocks for the
screw terminal type, use crimped
terminals and tighten the screw-down
terminals to the torque’s listed below.
8. All AC240V types are rated for double
coil voltage, both AC 220V AC 240V.
M4.5 screw
M4 screw
M3.5 screw
1a type
2a type
70
60
50
40
30
20
10
0
20°C
40°C
60°C
100
147 N-cm to 166.6 N-cm
(15 to 17 kg·cm)
117.6 N-cm to 137 N-cm
(12 to 14 kg·cm)
78.4 N-m to 98 N-cm
(8 to 10 kg·cm)
Coil applied voltage, %V
2.6 mm or 5.5 mm
2.0 mm or 3.5 mm
110
120
2
2
HE
5