Z15HW24B7K Omron, Z15HW24B7K Datasheet
Z15HW24B7K
Specifications of Z15HW24B7K
Related parts for Z15HW24B7K
Z15HW24B7K Summary of contents
Page 1
... F: 1.0 mm (split-contact models) Drip-proof • These Switches use a rubber boot on the actuator and adhesive fill between the case and cover to increase resistance to drips. • Models with drip-proof terminal protective covers and molded terminals with resin filling are also available. ...
Page 2
Model Number Legend Basic Models Z-@@@@-@ (1)(2)(3)(4) (5) (1) Ratings 01 : 0.1 A (micro load (2) Contact Gap H2 : 0.20 (extra-high-sensitivity 0.25 mm (high-sensitivity, micro load 0.5 mm (standard) E ...
Page 3
Ordering Information Main Unit Basic Models (General-purpose) Classification Actuator Contact gap Terminal *1 Pin plunger Slim spring plunger Short spring plunger Low OP Panel mount plunger Medium OP High OP Panel mount roller plunger Panel mount cross roller plunger Leaf ...
Page 4
Minimum Order Lot The following models are available at the minimum order lot specified below. Orders must be placed per lot. Classification Standard Actuator Short spring plunger Z-15GD-B Z-15GQ Panel mount plunger Z-15GQ-B Z-15GQ8-B Z-15GQ22 Panel mount roller plunger Z-15GQ22-B ...
Page 5
Standard, Microload Basic Models (Drip-proof Models Classification Contact gap Drip-proof terminal protective cover Terminal *1 Actuator Pin plunger Short spring plunger Low OP Spring plunger High OP Panel mount plunger Panel mount roller plunger Panel mount cross roller plunger Leaf ...
Page 6
Basic Models (Drip-proof Models High-sensitivity Classification Contact gap Drip-proof terminal protective cover Actuator Terminal * Flexible rod (steel wire Solder terminal : Screw terminal Specifications Ratings (Basic, Split-contact and Maintained contact Models) Z-15 (Except Micro Load and Flexible ...
Page 7
... Weight Approx *1. The values are for the plunger models. (For the lever models, the values are at the plunger section.) (Consult your OMRON representative for other models.) *2. The values are for the Z-15G pin plunger. *3. The values are for the Z-10FY-B. ...
Page 8
Structure Basic Models Contact Form (SPDT) COM NC NO Note: The Z-15GM is a reversible model and the NO and NC positions are reversed. Molded Terminals COM (Black) (Red) NC (White indicates wire color. Note: The Z-15GM ...
Page 9
Dimensions Mounting Use M4 screws with plane washers and spring washers to mount the Switch. Tighten each mounting screw securely to a torque of 1.18 to 1.47 N·m. Two, 4.2 dia. mounting holes or M4 25.4 ± 0.1 Basic Models ...
Page 10
Short Spring Plunger Z-15GD-B Z-01HD-B Z-15HD-B Z-10FDY-B Z-15ED-B Panel Mount Plunger PT Z-15GQ-B Z-01HQ-B Z-15HQ-B Z-10FQY-B Z-15EQ-B Z-15GQ3 Z-15GQ8 The external dimensions of the actuator vary. Z-15GQ-B OF 2. min. 1.12 N ...
Page 11
Panel Mount Cross Roller Plunger Z-15GQ21-B Z-15EQ21-B PT Z-15HQ21-B OP 15.5 16.3 Note: Do not use the M12 mounting screw and the case mounting hole at the same time, or the case may be damaged. Leaf Spring Z-15GL ...
Page 12
Low-force Hinge Lever Z-15GW4-B Z-15HW24-B Low-force Wire Hinge Lever Z-15HW52-B Z-15HW78-B (Lever Length: 110R The external dimensions of the actuator vary. Note: AC electrical ratings 125/250 V. Short Hinge Roller Lever Z-15GW22-B Z-01HW22-B Z-15HW22-B Z-10FW22Y-B Z-15EW22-B ...
Page 13
Short Hinge Cross Roller Lever Z-15GW49-B Z-15GW54-B (Lever Length: 48.7R) * 20.2 16.9 * The external dimensions of the actuator vary. Hinge Roller Lever Z-15GW25-B 20.2 16.9 Unidirectional Short Hinge Roller Lever Z-15GW2277-B 34.1 max. 20.2 16.9 Reverse Hinge Lever ...
Page 14
Basic Models (Drip-proof) without Terminal Protective Cover Terminals (Molded Terminals: Refer to page 21.) Without Terminal Protective Cover 9 ± 0.2 17.45 COM NO NC Three, M4 × 5.5 Terminal screws (with toothed 49.2 washer) ...
Page 15
Panel Mount Plunger Z-15GQ55 13.1 16.3 Panel Mount Roller Plunger Z-15GQ2255 15.5 16.3 Panel Mount Cross Roller Plunger Z-15GQ2155 15.5 16.3 Leaf Spring Z-15GL55 Note: Unless otherwise specified, a tolerance of ±0.4 ...
Page 16
Roller Leaf Spring Z-15GL255 4.2 Short Hinge Lever Z-15GW2155-B 20.2 16.9 4.2 Long Hinge Lever Z-15GW4455-B Hinge Lever Z-15GW55-B Short Hinge Roller Lever Z-15GW2255-B Z-01HW2255-B 20.2 16.9 4.2 Note: Unless otherwise specified, a tolerance of ±0.4 mm applies ...
Page 17
Hinge Roller Lever Z-15GW255-B 20.2 16.9 Unidirectional Short Hinge Roller Lever Z-15GW227755-B 34.1 max. 20.2 Reverse Hinge Lever * Z-15GM55-B 20.2 17.4 Reverse Short Hinge Roller Lever * Z-15GM2255-B 20.2 17.4 Reverse Hinge Roller Lever * Z-15GM255-B 20.2 17.4 * ...
Page 18
Flexible Rod (Coil Spring) Z-15GNJ55-B 38 (111.3) 43.4 (13.6) 16.3 +0.075 4.2 -0.025 Flexible Rod (Steel Wire) Z-15HNJS55-B 100 ± 0.4 (130.1) (22) (13.8) 16.3 +0.075 4.2 -0.025 Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all ...
Page 19
Basic Models (Drip-proof) with Terminal Protective Cover Dimensions and Operating Characteristics Pin Plunger Z-15GA55-B5V PT OP 19.2 Z-15GK3A55-B5V PT OP 19.2 Panel Mount Plunger PT Z-15GQA55-B5V OP 16.3 19.2 Panel Mount Roller Plunger PT Z-15GQ22A55-B5V OP 16.3 19.2 Panel Mount ...
Page 20
Long Hinge Lever Z-15GW44A55-B5V 20.2 16.9 19.2 Hinge Lever Z-15GWA55-B5V 20.2 16.9 19.2 Short Hinge Roller Lever Z-15GW22A55-B5V 20.2 16.9 19.2 Hinge Roller Lever Z-15GW2A55-B5V 20.2 16.9 19.2 Unidirectional Short Hinge Roller Lever Z-15GW2277A55-B5V 34.1 max. 20.2 16.9 Note: Unless ...
Page 21
... VSF (single-core, vinyl cord) 1.25 VCT (vinyl-insulated cable) Note models with molded terminals are approved by UL, CSA, or EN. 2. Molded terminals are not available on all models. Contact your OMRON representative for applicable products. Maintained-contact Models Dimensions and Operating Characteristics Pin Plunger PT ...
Page 22
... Do not use the switch alone in atmospheres such as flammable or explosive gases. Arcing and heat generation associated with switching may cause fires or explosions. • Switches are generally not constructed with resistance against water. Use a protective cover to prevent direct spraying if the switch is used in locations subject to splashing or spurting oil or water, dust adhering ...
Page 23
Tightening The suitable tightening torque for screw terminals is given below. Screw terminals except for those on Split-contact Models (Z-10FY- B): 0.78 to 1.18 N·m Screw terminals on Split-contact Models (Z-10FY-B): 0.49 to 1.18 N·m Operation • Make sure that ...
Page 24
... If an Actuator is used in a pressed state for an extended period of time at low temperatures, it may return slowly or it may not return at all. OMRON can provide special Actuators for use at low temperature with rubber boots or rubber caps made of silicon rubber, which has superior resistance to cold. Ask your OMRON representative for details ...
Page 25
... Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS ...