MBCC-412 BANNER ENGINEERING, MBCC-412 Datasheet

MBCC-412

Manufacturer Part Number

MBCC-412

Description

QUICK DISCONNECT CABLE, 4POS, STRAIGHT

Manufacturer

BANNER ENGINEERING

Type

Straight Femaler

Datasheets

1.MBCC-412.pdf (2 pages)

2.MQDEC-430SS.pdf (15 pages)

Specifications of MBCC-412

Cable Length

12ft

No. Of Contacts

Assembly Cable Type

PVC

Connector Type B

Stripped End Leads

Brand/series

MBCC

Cable, Length

Connector Type

Quick Disconnect

Indicator

LED

Length

4 m

Output Type

Solid State Relay

Primary Type

Cable

Response Time

4 ms

Sensor Type

Photoelectric

Standards

UL Recognized, CSA Certified

Temperature, Operating

-20 to +70 °C

Voltage, Rating

10 to 30 VDC

Voltage, Supply

10 to 30 VDC

Cable Assembly Type

Sensor

Connector Type A

Straight Circular Plug, 4 Positions, Socket Contacts

For Use With

Multi-Beam Series Sensors

Lead Free Status / Rohs Status

RoHS Exempt Product

Current page: 1 of 2
Download datasheet (68Kb)

Printed in USA

Model 3GA5-14:

The MULTI-BEAM Optical Edgeguide System is a unique sensor, used in pairs, to provide complete

edge-guidance sensing and control. Each sensor consists of a special MULTI-BEAM scanner block,

power block, and logic module. Each component is designed specifically for the edge-guiding

function. The scanner block, which contains a modulated emitter and receiver, works together with

the power block such that the emitter is gated "ON" only during positive half cycles of the 50/60Hz

power, and the receiver is gated "ON" only during the negative half cycles. The opposing sensor

operates the same way, except that it is wired with power leads L1 and L2 reversed from the way they

are connected to the first sensor. As a result, the sensor "A" emitter will only operate the sensor "B"

receiver, and vice-versa. This synchronization of the two sensors prevents unwanted crosstalk while

permitting very high excess gain.

The logic module includes both ON- and OFF-DELAY timing functions. The ON-DELAY ignores

short-term "nuisance" signals, and the OFF-DELAY permits a controlled amount of timed correction.

The logic modules have a LIGHT/DARK OPERATE programming jumper. Typically, the inboard

receiver is programmed for LIGHT OPERATE, and the outboard receiver for DARK OPERATE. In

this way, the web being guided is properly positioned in the "deadband" between the sensing beams

when one beam is broken and the other is not. The spacing between the beams is fixed at 1/2 inch (12,5

mm) and this becomes the "deadband" for edgeguiding. If tighter control is desired, the two sensors

may be mounted at an angle to the edge of the web such that the effective beam spacing is reduced to

1/2 inch times the cosine of the angle (see diagram at right).

The power block contains the same 3/4 amp solid-state switch as is used in standard MULTI-BEAM

power block models PBA and PBB, which will operate most ac solenoids, relays, or programmable

logic controllers (PLCs). The very high optical penetrating power (excess gain) plus rugged MULTI-

BEAM construction permits reliable control in harsh environments such as sawmills or power sanding

machines where conventional photoelectrics could not survive the contamination levels.

If necessary, optical penetrating power may be reduced by substituting model UC-D upper

covers.

SPECIFICATIONS, Optical Edgeguide System

Supply Voltage:

Output Configuration: SPST solid-state switch, 3/4 amp maximum (derated to 1/2 amp

at 70 degrees C). 10 amp maximum inrush for one second, or 30 amps for one ac cycle

(non-repeating). On-state voltage drop less than 2.5V ac at full load; off-state leakage

current less than 100 microamps.

Response Time: response time is a function of the ON and OFF delay timers, which are

independently adjustable over a useful range of from 1 to 15 seconds.

NOTE: shorter time ranges are available on a quote basis.

Construction: same as standard MULTI-BEAMs.

components totally encapsulated. Meets NEMA standards 1, 3, 12, and 13.

Range: 100 feet (30 m). Excess gain of 10,000X at 1 foot (30 cm).

NOTE: materials to be guided must be totally opaque.

Indicator LED: red LED status indicator on top of the housing is "on" when the receiver

detects modulated light (unblocked) condition.

Operating Temperature Range: -40 to +70 C (-40 to +158 F).

MULTI-BEAM

100,000

10,000

1,000

100

.1 FT

Excess Gain Curve

1 FT

DISTANCE

Excess Gain,

MULTI-BEAM

Edgeguide System

10 FT

120V ac

model 3GA5-14, 105 to 130V ac (50/60Hz)

model 3GB5-14, 210 to 250V ac (50/60Hz)

100 FT

Model 3GB5-14:

Optical Edgeguide System

Functional Schematic, Optical Edgeguide System

Reinforced VALOX

220/240V ac

housing;

SENSITIVITY control accessible beneath lower cover.

See drawing next page.

Dimension Drawing

Deadband Adjustment

P/N 03506D5B

Related parts for MBCC-412

MBCC-412 Summary of contents

Page 1

MULTI-BEAM Model 3GA5-14: 120V ac The MULTI-BEAM Optical Edgeguide System is a unique sensor, used in pairs, to provide complete edge-guidance sensing and control. Each sensor consists of a special MULTI-BEAM scanner block, power block, and logic module. Each component ...

Page 2

... MULTI-BEAMs includes cord grips for .1- to .4-inch diameter cable and lockwasher. Model MBC-4 (right 4-pin male industrial duty connector that threads into the base of all MULTI-BEAMs. MBCC-412 is a 12-foot long (3,6m) mini-type cable interchangeable with standard industry types of several manufacturers. Typical Hookup Diagram ...

Related keywords

MBCC-412 datasheet
MBCC-412 data sheet
MBCC-412 pdf datasheet
MBCC-412 component
MBCC-412 part
MBCC-412 distributor
MBCC-412 RoHS
MBCC-412 datasheet download