T183E BANNER ENGINEERING, T183E Datasheet - Page 4

• Manufacturer Part Number: T183E
• Description: Photoelectric Sensor
• Manufacturer: BANNER ENGINEERING
• Type: Opposed Moder

Specifications of T183E

• Output Current: 300mA
• Sensor Input: Optical
• Sensing Range Max: 20m
• Contact Current Max: 150mA
• Switch Terminals: Cable
• Sensing Mode: Opposed
• Brand/series: T18
• Current, Switching: 300 mA
• Humidity: 90% @ 50 °C (Non-Condensing)
• Ip Rating: IP69K
• Length, Cable: 6.5 ft.
• Material, Housing: PBT Polyester
• Material, Lens: Polycarbonate⁄Acrylic
• Mounting Type: Threaded
• Output: SPST
• Primary Type: Photoelectric
• Range, Measurement: 66 mm
• Response Time: 3 ms (ON), 1.5 ms (OFF)
• Standards: CE Mark, CSA Certified, UL Listed
• Technology: Photoelectric
• Temperature, Operating: -40 to +70 °C
• Termination: Cable
• Vibration: 10 to 60 Hz (Max.)
• Voltage, Supply: 250 VAC
• Lead Free Status / Rohs Status: RoHS Exempt Product

4
Supply Voltage and
Current
Supply Protection
Circuitry
Output Configuration
Output Rating
Output Protection
Circuitry
Output Response Time
Repeatability
Adjustments
Indicators
Construction
Environmental Rating
Connections
Operating Conditions
Vibration and Mechanical
Shock
Certifications
P/N 121525
T18 Sensors – ac-Voltage Series
20 to 250V ac (50/60 Hz)
Average current: 20 mA
Peak current: 200 mA @ 20V ac, 500 mA @ 120V ac, 750 mA @ 250V ac
Protected against transient voltages
SPST solid-state ac switch; three-wire hookup; light operate or dark operate, depending on model
300 mA maximum (continuous)
Inrush capability: 1 amp for 20 milliseconds, non-repetitive
OFF-state leakage current: < 100 microamps
ON-state saturation voltage: 3V @ 300 mA ac; 2V @ 15 mA ac
Protected against false pulse on power-up
Opposed mode: 16 milliseconds ON, 8 milliseconds OFF
Other models: 16 milliseconds ON and OFF
NOTE: 100 millisecond delay on power-up; outputs do not conduct during this time.
Opposed mode: 2 milliseconds
Other models: 4 milliseconds
Repeatability and response are independent of signal strength.
Non-polarized retro and diffuse models (only) have a single-turn rear-panel Sensitivity control (turn clockwise to
increase gain).
Two LEDs (Green and Yellow)
PBT polyester housing; polycarbonate (opposed-mode) or acrylic lens
Leakproof design rated NEMA 6P, DIN 40050 (IP69K)
2 m (6.5') attached cable or 4-pin Micro-style quick-disconnect fitting
Temperature: -40° to +70° C (-40° to +158° F)
Maximum relative humidity: 90% at 50° C (non-condensing)
All models meet Mil. Std. 202F requirements. Method 201A (Vibration; frequency 10 to 60 Hz, max., double
amplitude 0.06" acceleration 10G). Method 213B conditions H&I (Shock: 75G with unit operating; 100G for
non-operation)
Light Operate: Output conducts when sensor sees its own (or the emitter’s) modulated light
Dark Operate: Output conducts when the sensor sees dark
Fixed-Field models: derate 5 mA/°C above +50° C (+122° F)
Green ON steady: power to sensor is ON
Yellow ON steady: sensor sees light
Yellow flashing: excess gain marginal (1 to 1.5x) in light condition
Specifications
Banner Engineering Corp.
www.bannerengineering.com • Tel: [phone]
•
Minneapolis, MN U.S.A.