Q20NDXLQ5 BANNER ENGINEERING, Q20NDXLQ5 Datasheet - Page 3

• Manufacturer Part Number: Q20NDXLQ5
• Description: Photoelectric Sensor
• Manufacturer: BANNER ENGINEERING

Specifications of Q20NDXLQ5

• Output Current: 100mA
• Sensor Output: NPN
• Supply Voltage Range Dc: 10V To 30V
• Sensor Housing: Rectangular
• Sensor Input: Optical
• Body Material: ABS
• Supply Voltage Max: 30VDC
• Sensing Range Max: 1500mm

QD models:
† Range is specified using a model BRT-84 reflector.
**Available with Health or Alarm Mode output; contact factory for details.
WORLD-BEAM Q20 Series Sensors
P/N 127816 rev. E
• For 4-pin Pico-style (threaded) integral QD, add suffix “Q7” (e.g., Q20EQ7).
• For 4-pin Pico-style (threaded) 150 mm (6") pigtail QD, add suffix “Q” (e.g., Q20EQ).
• For 4-pin Euro-style 150 mm (6") pigtail QD, add suffix “Q5” (e.g., Q20EQ5).
• For 150 mm (6") PUR pigtail cable with 4-pin threaded Euro-style QD connector, add “QPMA” to model number (e.g., Q20EQPMA)
Supply Voltage
Supply Protection Circuitry
Output Configuration
Output Response Time
Indicators
Adjustments
Fixed-Field: 10 to 30V dc (10% maximum ripple within
specified limits) at less than 25 mA, exclusive of load
All others: 10 to 30V dc (10% maximum ripple within
specified limits) at less than 18 mA, exclusive of load
Protected against reverse polarity and transient voltages
100 mA with short circuit protection
OFF-state leakage current:NPN: < 200 µA sinking;
PNP: < 20 µA sourcing
ON-state saturation voltage:NPN: < 1.6V @ 100 mA;
PNP: < 3.0V @ 100 mA
Opposed Mode: 1 millisecond ON/600 microseconds
OFF
Fixed-Field: 3 milliseconds ON/1.5 milliseconds OFF
All others: 800 microseconds ON/OFF
Note:100 millisecond delay on power-up; outputs do not
conduct during this time
Two LED Indicators: Power (green) and Output (yellow)
Fixed-Field models:
Green ON Steady: Power ON
Yellow ON Steady: Black (LO) wire conducting
All other models:
Green ON Steady: Power ON
Green flashing: Output overloaded
Yellow ON steady: Black (LO) wire conducting
Yellow flashing: Marginal excess gain (1 to 1.5X)
Black (LO) wire conducting
Diffuse, Retroreflective, and Polarized Retroreflective
models (only):
Single-turn Sensitivity (Gain) adjustment potentiometer
www.bannerengineering.com - tel: [phone]
Specifications
Repeatability
Construction
Connections
Operating Conditions
Environmental Rating
Vibration and Mechanical Shock
Application Notes
Certifications
Opposed Mode: 140 microseconds
Fixed-Field: 182 microseconds
All others: 155 microseconds
Housing: ABS
Lenses: PMMA
Gain Adjuster: PBT (Retro and Diffuse models only)
2 m (6.5') or 9 m (30') 4-wire PVC cable, 150 mm (6")
pigtail with 4-pin threaded Pico-style (Q) or
Euro-style (Q5) connector, or 4-pin integral threaded
Pico-style connector (Q7), depending on model
Temperature: –20° to +60° C (–4° to +140° F)
Relative Humidity: 95% @ 50° C (non-condensing)
IEC IP67 (NEMA 6)
1200 PSI washdown NEMA ICS 5
Annex F-2002
All models meet Mil. Std. 202F requirements method
201A (vibration: 10 to 60 Hz max., double amplitude
0.06", maximum acceleration 10G). Also meets IEC
947-5-2; 30G 11 ms duration, half sine wave
Opposed mode sensor spacing can be reduced by al-
ternating emitters and receivers or by applying cross
talk filters (visible red models only)
3