CX-21 PANASONIC EW, CX-21 Datasheet - Page 4

• Manufacturer Part Number: CX-21
• Description: PHOLOELECTRIC SENSOR
• Manufacturer: PANASONIC EW

Specifications of CX-21

• Output Current: 100mA
• Sensor Output: NPN Open Collector
• Supply Voltage Range Dc: 12V To 24V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

OPTIONS
Notes: 1) RF-11 cannot be used with CX-28IR .
Notes:
Notes:
Notes:
Sensor mounting bracket
• MS-CX2-1
Two M3 (length 12mm)
screws with washers
are attached.
• MS-CX2-5
Two M3 (length 12mm)
screws with washers
are attached.
Reflector
(
Reflector
mounting
bracket
Reflective tape
(For CX-29
Sensor mounting
bracket
(Note 2)
Universal sensor
mounting stand
(Note 3)
Sensor checker
(Note 4)
Designation
For retro-
reflective type
sensor only
2) The plug-in connector type sensor does not allow use of some sensor
3) Refer to P.310l for details of the universal sensor mounting stand.
4) Refer to P.378l for details of the sensor checker CHX-SC2.
mounting brackets because of the protrusion of the connector.
only)
)
RF-210
RF-220
MS-RF21-1
MS-RF22
MS-RF23
RF-11 (Note 1)
RF-12
MS-CX2-1
MS-CX2-2
MS-CX2-4
MS-CX2-5
MS-CX-3
MS-AJ
MS-AJ-A
MS-AJ-M
CHX-SC2
Model No.
• MS-CX2-2
• MS-CX-3
Two M3 (length 12mm)
screws with washers
are attached.
Two M3 (length 12mm)
screws with washers
are attached.
• Sensing range: 0.1 to 1m [CX-29 ]
• Min. sensing object: " 30mm
• Sensing range: 0.1 to 1.5m [CX-29 ]
• Min. sensing object: " 35mm
Protective mounting bracket for RF-210
It protects the reflector from damage and maintains alignment.
For RF-220
For RF-230
• Ambient temperature:
• Ambient humidity:
Notes: i) Keep the tape free from
Notes:
Foot angled mounting bracket
It can also be used for mounting RF-210.
(The thru-beam type sensor needs two brackets.)
Foot biangled mounting bracket
Flat mounting saves height.
It can also be used for mounting RF-210.
(The thru-beam type sensor needs two brackets.)
Protective mounting bracket
It protects the sensor from damage and maintains alignment.
(The thru-beam type sensor needs two brackets.)
Back biangled mounting bracket
Suitable for sensing from bottom of conveyors, etc.
(The thru-beam type sensor needs two brackets.)
Back angled mounting bracket
(The thru-beam type sensor needs two brackets.)
Basic assembly
Lateral arm assembly
Assembly for reflector
It is useful for beam alignment of thru-beam type sensors.
The optimum receiver position is given by indicators, as
well as, an audio signal.
ii) Do not cut the tape.
stress. If it is pressed
too much, its capability
may deteriorate.
It will deteriorate the
sensing performance.
35 to 85% RH
• MS-CX2-4
Two M3 (length 14mm)
screws with washers
are attached.
25 to
50 to 250mm [CX-28IR ]
50 to 500mm [CX-28IR ]
Description
50 C
• Sensing range:
• Sensing range:
0.1 to 0.7m [CX-29 ]
0.15 to 0.4m [CX-28IR ]
0.1 to 0.5m [CX-29 ]
Universal sensor mounting stand
• MS-AJ
• MS-AJ-M
Elevation
angle
Elevation
angle
45
45
45
45
45
45
Swivel:
360 rotation
Swivel:
360 rotation
Mounting holes
for M6 screw
Mounting holes
for M6 screw
12.8
mm
8mm
Height
adjustment:
150mm
approx.
Height
adjustment:
150mm
approx.
Reflector
• RF-210
Reflective tape
• RF-11
Reflector mounting bracket
• MS-RF23
Two M4 (length 10mm)
screws with washers
are attached.
• MS-RF21-1
Two M3 (length 12mm)
screws with washers
are attached.
33.3mm
30mm
With the lateral arm,
the sensor can sense
from above a
production line.
360
rotation
• MS-AJ-A
11mm
Sensor checker
0.7mm
Sensor checker
45
42.3mm
angle
adjustment
25mm
CX-20
45
• RF-220
• RF-12
• MS-RF22
Two M3 (length 8mm)
screws with washers
are attached.
30mm
35.3mm
Swivel:
360 rotation
Mounting holes
for M6 screw
Height
adjustment:
150mm
approx.
0.7mm
8.3mm
163