Ultrasonic Slot Sensor

SLM10B6

Manufacturer Part NumberSLM10B6
DescriptionUltrasonic Slot Sensor
ManufacturerBANNER ENGINEERING
TypeOpposed Mode
SLM10B6 datasheets
 

Specifications of SLM10B6

Sensing Range Min0.76mmSensing Range Max10mm
Operating Temperature Range-20°C To +60°CSupply Voltage30VDC
Body MaterialDie-cast ZincSensor TerminalsCable
FeaturesOpposed-ModeBrand/seriesSLM
Current, Switching100 mAFunctionVane
Ip RatingIP67OutputNPN/PNP
Primary TypePhotoelectricRange, Measurement10 mm
Sensing ModeOpposedTechnologyPhotoelectric
Termination4-Wire CableVoltage, Supply30 VDC
Accessories AvailableCordsetsContact Rating25 MA
Sensor OutputNPN/PNPSensor Body MaterialDie-cast Zinc
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
Page 3/6

Download datasheet (519Kb)Embed
PrevNext
Slot Opening
10, 20, 30, 50, 80, 120, 180, or 220 mm (depending on model); beam is 5 mm (0.2") from outer edge
Supply Voltage and Current
10 to 30V dc (10% ripple) @ less than 25 mA, exclusive of load
Supply Protection Circuitry
Protected against reverse polarity and transient voltages
Output Configuration
Cabled and Euro-style QD models: Bipolar: One current sourcing (PNP) and one current sinking (NPN)
Pico-style QD models: Current sourcing (PNP) or current sinking (NPN), depending on model
Output Rating
100 mA with short circuit protection
OFF-state leakage current: < 10 µA sourcing; < 200 µA sinking
ON-state saturation voltage:
NPN: 1.6V @ 100 mA
PNP: 2.0V @ 100 mA
Output Protection Circuitry
Protected against output short-circuit and false pulse on power up. 100 ms max. delay at power up; outputs do not
conduct during this time.
SLM10…
Minimum Object Detection*
1.00 mm
(0.040")
at Max. Gain
Minimum Object Detection*
0.30 mm
(0.012")
at 2X Excess gain
Hysteresis**
0.10 mm
(0.004")
Repeatability***
0.02 mm
(0.001")
Output Response Time
500 microseconds
Repeatability
95 microseconds
Adjustments
1-turn potentiometer Sensitivity adjustment
Light Operate / Dark Operate selection switch
Indicators
Two LED Indicators: Power (green) and Output (yellow)
Green ON steady: Power ON
Green flashing:
Yellow ON steady: Output is activated
Construction
Housing: Die-cast zinc with yellow paint; model numbers with suffix “N” have nickel plating
Endcaps: ABS
Optic windows: acrylic
Environmental Rating
IEC IP67 (NEMA 6)
Connections
Cabled models: 2 m (6.5') or 9 m (30') 4-conductor, PVC-jacketed cable
Pico-style QD models: 3-pin, threaded integral QD connector
Euro-style QD models: 150 mm (6") pigtail (polyurethane) cable with 4-pin, threaded connector
Operating Conditions
Temperature: –20° to +60° C (– 4° to +140° F)
Max. Relative Humidity: 95% @ 55° C (non-condensing)
Certifications
* Minimum Object Detection: Smallest diameter rod that can be detected when passed slowly through sensing beam
NOTE: Minimum object detection is measured midway between the emitter and receiver. For best results, objects to be detected should be placed in the midway position
when possible. The minimum object detection size may increase if the object is very close to the receiver side.
**Hysteresis: Distance an object must move to toggle between output OFF and output ON state
***Repeatability: Variation in switching distance for a standard target at controlled sensing conditions
Banner Engineering Corp. • Minneapolis, MN U.S.A
www.bannerengineering.com • Tel: 763.544.3164
SLM Series Slot Sensors
Specifications
SLM20…
SLM30…
SLM50…
1.25 mm
1.50 mm
1.65 mm
(0.050")
(0.060")
(0.065")
0.30 mm
0.40 mm
0.60 mm
(0.012")
(0.016")
(0.024")
0.10 mm
0.10 mm
0.10 mm
(0.004")
(0.004")
(0.004")
0.02 mm
0.02 mm
0.04 mm
(0.001")
(0.001")
(0.002")
Sensor short circuit
SLM80…
SLM120…
SLM180…
1.80 mm
1.80 mm
1.80 mm
(0.070")
(0.070")
(0.070")
0.75 mm
0.90 mm
0.90 mm
(0.030")
(0.035")
(0.035")
0.20 mm
0.20 mm
0.20 mm
(0.008")
(0.008")
(0.008")
0.06 mm
0.08 mm
0.08 mm
(0.002")
(0.003")
(0.003")
P/N 122703 rev. D
SLM220…
2.40 mm
(0.095")
1.00 mm
(0.039")
0.20 mm
(0.008")
0.08 mm
(0.003")
3