T186UEQ BANNER ENGINEERING, T186UEQ Datasheet - Page 2

• Manufacturer Part Number: T186UEQ
• Description: ULTRASONIC SENSOR EMITTER
• Manufacturer: BANNER ENGINEERING
• Type: Emitterr

Specifications of T186UEQ

• Switching Frequency: 230kHz
• Operating Temperature Range: -40°C To +70°C
• Brand/series: T18U
• Current, Switching: 150 mA
• Ip Rating: IP67
• Mounting Type: Threaded
• Primary Type: Photoelectric
• Range, Measurement: 60 cm
• Sensing Mode: Opposed
• Technology: Ultrasonic
• Termination: Cable
• Voltage, Supply: 30 VDC
• Lead Free Status / Rohs Status: RoHS Exempt Product

Specifications
Sensing range:
NORMAL resolution mode: to 24 inches (60 cm)
HIGH resolution mode: to 12 inches (30 cm)
Sensing beam:
Minimum spacing (adjacent pairs):
5 cm for emitter-to-receiver separations of up to 15 cm.
Add 1 cm of adjacent-pair spacing for every 10 cm of emitter-to-
receiver spacing beyond 15 cm.
Supply voltage:
Supply current:
exclusive of output load.
Receiver output configuration:
T18VN models: NPN sinking, N.O. and N.C. (complementary)
T18VP models: PNP sourcing, N.O. and N.C. (complementary)
Receiver output rating:
derated to 100 mA at 70 C (derate 1 mA per C).
Both outputs may be used simultaneously.
On-state saturation voltage: <1.5 V at 10 mA; <2.0 V at 150 mA
Off-state leakage current: < 1 microamp at 30V dc
Output protection: Overload and short-circuit protected.
No false pulse upon receiver power-up: false pulse protection causes
Response time:
NORMAL resolution mode: 2 milliseconds “on” and “off”
HIGH resolution mode: 1 millisecond “on” and “off”
Rep rate:
NORMAL resolution mode: 125 Hz maximum
HIGH resolution mode: 200 Hz maximum.
Mechanical sensing repeatability at 12 inch (30 cm) range:
NORMAL resolution mode: <0.08 inch (<2 mm)
HIGH resolution mode: <0.04 inch (<1 mm)
Sensing resolution:
Beam angle (-3dB full angle):
Indicators:
have two LEDs, one yellow and one green. Indications are as follows:
Green glowing steadily = dc power “on”
Green flashing = output overloaded
Yellow flashing = sonic signal received (flash rate is proportional to
received signal strength; flash is from full to half intensity).
Construction:
VALOX
Mating jam nut is supplied for mounting. Acoustic face is epoxy reinforced.
Circuitry is epoxy-encapsulated. Rated NEMA 6P, IEC IP67.
NOTE: VALOX
Cabling options:
Emitters: 6 1/2 foot long (2 m) attached PVC-covered 2-wire cable or
4-pin euro-style quick disconnect fitting.
Receivers: 6 1/2 foot long (2 m) attached PVC-covered 4-wire cable or
4-pin euro-style quick disconnect fitting.
30-foot long cables are available by request.
Mating euro-style quick disconnect cables are also available (page 3)
a 100 millisecond delay upon power-up.
T18U Series
®
back cover. Transducer housing is threaded M18 x 1.
Emitters have a green LED for dc power “on”. Receivers
®
Patented* T-style yellow VALOX
ultrasonic, 230 KHz.
(no minimum range)
is a registered trademark of General Electric Co.
12 to 30V dc, 10% maximum ac ripple.
50 mA (emitters); 35 mA (receivers),
(See Tables, page 4)
150 mA maximum each output at 25 C,
15 2
®
housing with black
Dimensions
Cabled models shown below. QD connector adds 0.6 inches
(15,0 mm) in overall height to quick-disconnect models (see
also drawings on page 3).
Vibration and mechanical shock:
Meets Mil. Std 202F requirements.
Method 201A (Vibration: frequency 10 to 60 Hz, max., double amplitude
0.06-inch, maximum acceleration 10G).
Method 213B conditions H & I (Shock: 75G with unit operation:
100G for non-operation)
Also meets IEC 947-5-2 requirements: 30G, 11 ms duration, half sine
wave.
Operating temperature range:
Signal Strength Indicator
Front
Rear
Power Indicator
(Receiver, Only)
Green LED
(Supplied)
M18 x 1
Yellow LED
Thread
Jam Nut
11.5 mm
ø 15 mm
(0.45 in)
(0.59 in)
ø 40.0 mm
(1.57 in)
-40 to +70 C (-40 to 158 F)
51.5 mm
(2.03 in)
30.0 mm
(1.18 in)