T30UDNB BANNER ENGINEERING, T30UDNB Datasheet
T30UDNB
Specifications of T30UDNB
Related parts for T30UDNB
T30UDNB Summary of contents
Page 1
... T30UDNAQ (5.9" to 39") T30UDPA 228 kHz T30UDPAQ T30UDNB 300 T30UDNBQ (11.8" to 79") T30UDPB 128 kHz T30UDPBQ **NOTES: • (30') cables are available by adding suffix “W/30” to the model number o f any cabled sensor (e.g., Q45UDNA W/30). • A model with a QD connector requires an optional mating cable; see page 8. ...
Page 2
... Use the procedures as described, or combine them for specialized applications. NOTE: Output 1 = White wire Output 2 = Black wire 2 P/N 59200 Rev. D Red Signal Strength LED Yellow Output 2 LED SIGNAL OUTPUT 2 Output 2 BLACK Programming Push Button DUAL DISCRETE ™ ™ Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 ...
Page 3
... A Single Pair of Sensing Window Limits with Complementary Outputs Output 1 Output 2 Output 1 Sensing Range Figure 2c. Programming a single pair of sensing window limits, complementary outputs Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 U-GAGE ™ T30 Series with Dual Discrete Outputs General Notes on Programming: 1. ...
Page 4
... NOTE: Hold the Remote line high > 2 seconds (before teaching the second limit) to exit PROGRAM mode without saving any changes. The sensor will revert to the last saved program. Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 Output 1 ...
Page 5
... U-GAGE Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 ™ T30 Series with Dual Discrete Outputs RUN Mode NOTE: All LED indicators momentarily go OFF when sensor changes state between PROGRAM and RUN modes. Signal LED The red Signal LED indicates the strength and condition of the sensor’s incoming signal. ...
Page 6
... Flashing = Relative received signal strength Yellow ON = Output is conducting Green OFF = PROGRAM mode Red Flashing = Relative received signal strength ON = Ready for first window limit { Yellow Flashing = Ready for second limit OFF = Not teaching this output Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 ...
Page 7
... Jam Nut (Supplied) M30 x 1.5 Thread 45.0 mm (1.77") ø (0.59") Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 U-GAGE ™ T30 Series with Dual Discrete Outputs U-GAGE T30 Series Performance Curves With Plate Target (Typical) 400 mm 8 ...
Page 8
... Quick-Disconnect PNP Output 1 bk Output 2 gy Remote Teach shield* Pin-out ø (0.6") M12 x 1 Brown Wire Black Wire 38 mm max. (1.5") Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 + – + 12-24V dc – White Wire Blue Wire Gray Wire ...
Page 9
... Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 U-GAGE ™ T30 Series with Dual Discrete Outputs Mounting Brackets SMB1815SF The 15 mm diameter hub of the T30 is mounted into the swivel using two set screws. ø ...
Page 10
... U-GAGE ™ T30 Series with Dual Discrete Outputs 10 P/N 59200 Rev. D Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 ...
Page 11
... U-GAGE Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 ™ T30 Series with Dual Discrete Outputs 11 P/N 59200 Rev. D ...
Page 12
... T30 Series with Dual Discrete Outputs WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period ...