K3MA-J 100-240VAC Omron, K3MA-J 100-240VAC Datasheet
K3MA-J 100-240VAC
Specifications of K3MA-J 100-240VAC
K3TJ-V111R
K3TJ-V111R
Related parts for K3MA-J 100-240VAC
K3MA-J 100-240VAC Summary of contents
Page 1
... Note: Rubber packing is provided with the Controller. ■ Accessories (Order Separately) Name Splash-proof Soft Cover Hard Cover 3. Supply Voltage 100-240VAC: 100 to 240 VAC 24VAC/VDC: 24 VAC/VDC Output None K3MA-J 100-240VAC 2 relay contact outputs (SPST-NO) K3MA-J-A2 100-240VAC None K3MA-J 24VAC/VDC 2 relay contact outputs (SPST-NO) K3MA-J-A2 24VAC/VDC Shape K32-49SC K32-49HC ...
Page 2
... Specifications ■ Ratings Model K3MA-J 100-240VAC, K3MA-J-A2 100-240VAC Supply voltage 100 to 240 VAC Operating voltage range 85% to 110% of the rated supply voltage Power consumption 6 VA max. (under maximum load) Insulation resistance 20 MΩ min. (at 500 VDC) between external terminal and case. ...
Page 3
... MΩ min. (at 23±3°C) ±0.1% FS ±1 digit max. (at 23±5°C) ±0.1% FS ±1 digit max. 45 Ω (at 23±3°C) Resistive load (cosφ 1 250 VAC, 1 VDC 250 VA K3MA-J Displayable range –19999 to 99999 (with scaling function) Inductive load (cosφ = 0.4, L/R=7 ms) 3 ...
Page 4
... Analog input Outputs Key Input circuit Micro- Display computer EEPROM Output X circuit Constant voltage circuit Power supply circuit To A/D Current input B A+B=1 MΩ COM K3MA-J Models with A1 E1 comparative output A2 E2 OUT1 OUT2 Voltage input E5 E5 COM E6 E6 For voltage input ...
Page 5
... Selects DC voltage/current signal input Note: The initial value for the input range is “ (4-20).” Scaling • Analog (Process) Inputs The K3MA-J converts input signals into desired physical values. INPUT2: Any input value DISPLAY2: Displayed value corresponding to INPUT2 INPUT1: Any input value DISPLAY1: Displayed value corresponding to INPUT1 When DISPLAY1 is set for INPUT1, and DISPLAY2 is set for INPUT2, a line will be displayed joining the two points ...
Page 6
... Convenient Functions Scaling Teach The parameters (inp.1, inp.2) for the K3MA-J’s initial setting level can be set using actual input values with the teaching function. After displaying the parameters, the actual input settings can be made with the following operation. “T” lights to ...
Page 7
... Parameter Setting value init off on Use this to reset the K3MA-J after returning it to its factory-set condi- tion. Average Processing Average processing stabilizes displayed values to minimize flicker by averaging the fluctuating input signals. Average processing can be performed for the measurement values in either of four steps (OFF, 2 times, 4 times times) ...
Page 8
... T Lit when the teaching function is operable. Blinks while the teaching function is operating. 3. Level indicator Displays the current level that the K3MA-J is in. (See below for details.) 4. MAX/MIN Key Used to display the MAX and MIN values when a measurement value is being displayed. 5. Level Key Used to change the level ...
Page 9
... Wiring • Use the following M3 crimp terminals. ■ Unit Labels (Provided) • The unit labels are not attached to the K3MA-J. Select the desired labels from the provided sheet. Note: For scales and gauges, use the unit labels that are specified by the relevant laws or regulations ...
Page 10
... Mode Key Mode Key Note: When a comparative value is displayed, it can be changed by pressing the Shift Key and the Up Key (when key protection is OFF). Function K3MA-J MAX/MIN Key MAX/MIN Key MIN value OUT2 value OUT2 OUT2 upper-limit lower-limit value ...
Page 11
... Indicates change of level. Note: The move-to-protect-level time can be set in the advanced-function setting level. Power ON Operation level + Flashing stops if key 1 s min. is released min min. -1234.5 Continue to press the key for 2 s min. Initial setting level Password "−0169" min. Advanced-function setting level K3MA-J 11 ...
Page 12
... Parameters Note: 1. Some parameters are not displayed for certain models. 2. The K3MA-J will stop measurement if the level is changed to the initial setting level or the advanced-function setting level the input range is changed, some parameters are set to default values. Therefore, set the input range first. ...
Page 13
... Enter password / / "−0169" − − Models with the compar- ative − output function − − When zero- limit is ON − − K3MA-J Parameter / initialization MODE Average / / / processing Unit: times MODE OUT1 − − hysteresis MODE OUT2 hysteresis − − MODE ...
Page 14
... Shift to advanced- function setting level values, auto-zero limit value, display color change, display auto-return time, or move-to-protect-level time. Press the Level Key operation level. Specify set value of OUT 1 and 2. operation K3MA Power ON for 3 s min. to move to the initial setting for less than 1 s min. to return to the Measurement starts ...
Page 15
... LEVEL MODE SHIFT UP 1. Set the K3MA-J input type to the input range. Parameter: in-t (input type), Setting value: 4-20 2. Set the display values for the corresponding input values. Set the scaling as shown below for the following correspondence: input 4 mA-->display 0.0, input 20 mA-->display 980.0 Parameter inp ...
Page 16
... Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS ...