E3XDA41S Omron, E3XDA41S Datasheet - Page 12

• Manufacturer Part Number: E3XDA41S
• Description: PHOTOSWITCH, FIBRE, PNP
• Manufacturer: Omron

Specifications of E3XDA41S

• Svhc: No SVHC (15-Dec-2010)
• Supply Voltage Dc Max: 24VDC
• Dielectric Strength Vdc: 1000VAC
• External Depth: 10mm
• External Length / Height: 32mm
• External Width: 70mm
• Ip/nema Rating: IP 50
• Insulation: RoHS Compliant
• Output Current: 50mA
• Output Type: PNP
• Response Time: 1ms
• Rohs Compliant: Yes
• Insulation Resistance: 20Mohm

Nomenclature
Amplifier Units
Common adjustment methods
1. Setting the Operation Mode
The operation mode is set with the Mode Selector.
2. Adjusting the Power (RUN Mode)
The current incident light level can be adjusted to near the power
tuning target value (default: 2,000).
*1. Further sensor specifc functions are described in the attached instruction sheets of fiber amplifiers (E3X-DA@@RM-S, E3X-DA@@TW-S)
A-408
* E3X-DA@TW-S: The operation mode is set in SET mode. Refer to
* E3X-DA@TW-S: Set the Channel Selector to the desired channel
* Confirm that the MODE key setting is PTUN (power tuning). The
Operation Indicator (orange)
ON when output is ON.
OFF when output is OFF.
page 410, 5. Convenient Functions.
before making any adjustments or settings. This is true for all ad-
justments and settings.
default setting is PTUN. Refer to page 410, 5. Convenient Func-
tions
E3X-DA@-S
E3X-DA@RM-S
Release the key after
the progress bar
is displayed.
The Power Tuning indicator
will light when the adjustment
has been completed.
Set the Mode Se-
lector to RUN.
Lock Button
Locks the fiber.
Light ON
Dark ON
(Factory-set to RUN)
Main Display (Red)
Incident level,
function, etc.
Operation mode
RUN
Display changes after
specific time.
Power Tuning
Indicator
ON: Power
tuning is set.
Sub-Display (Green)
Threshold, function
settings, etc.
D·ON
L·ON
Power tuning
target value
Light level
PTUN
Light level
Mode Selector
Use to select SET or RUN mode.
Operation Keys
Function setting operations
*1
L
Threshold (default)
MODE
UP
DOWN
MODE
Operation Mode Selector
Use to switch between Light
ON and Dark ON modes.
Threshold
Operation
Progress bar
3 s
D
(Factory-set)
* Setting Errors
An error has occurred if one of the following displays appears after
the progress bar is displayed.
Note: Press the DOWN key right after pressing the MODE key.
3. Setting Thresholds Manually
A threshold can be set manually. A threshold value can also be fine-
tuned using manual setting after teaching.
Operation indicator
for channel 1 (orange)
ON when output is ON.
OFF when output is OFF.
* Even if the display method for display switching is changed, the
threshold will appear on the sub-display when the key is pressed.
(RUN Mode)
E3X-DA@TW-S
Set the Mode Se-
lector to RUN.
To restore the default
power settings:
"OFF" will flash twice.
The Power Tuning indicator
will go out when the default
setting has been restored.
PTUN
PTUN
Lock Button
Locks the fiber.
(Factory-set to RUN)
Main Display (Red)
Incident level,
function, etc.
Display
RUN
Flashes twice
Flashes twice
Operation indicator
for channel 2 (orange)
ON when output is ON.
OFF when output is OFF.
BOTM
OVER
Advanced Photoelectric Sensors
Sub-Display (Green)
Threshold, function
settings, etc.
Increases threshold.
The incident light
The incident light
level is too high
level is too low
Bottom Error
for the power
for the power
tuning target
tuning target
Over Error
Light level
Light level
PTUN
Error
value.
value.
Press together (see note).
Mode Selector
Use to select SET or RUN mode.
DOWN
UP
Operation Keys
Function setting operations
Channel Selector
Use to switch between
channels 1 and 2.
UP
DOWN
MODE
Threshold (default)
Threshold
turned to the minimum
be decreased down to
tuned. The power can
approximately 5 times
The power will not be
level. The power can
approximately 1/25th
be increased up to
DOWN
Decreases threshold.
The power will be
the incident light
the incident light
MODE
OFF
Action
value.
value.
3 s