KPEG623AN Kingstate Electronics Corp., KPEG623AN Datasheet - Page 3

• Manufacturer Part Number: KPEG623AN
• Description: PIEZO BUZZER, PANEL MOUNT
• Manufacturer: Kingstate Electronics Corp.

Specifications of KPEG623AN

• Tones: Slow Pulse
• Resonant Frequency: 2.8kHz
• Sound Level Spl: 82dB
• Sound Level Distance: 30cm
• Current Consumption: 16mA
• Current Rating: 16mA
• External Diameter: 42.5mm
• External Length / Height: 42mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

D. MEASURING METHOD 測量方法
E. MECHANICAL CHARACTERISTICS 機械特性
No.
S.P.L. Measuring Circuit 音壓測試接線圖
1
2
3
4
5
Mic : RION S.P.L meter UC30 or equivalent
Mic：RION 噪音計 UC30 或同等品
Terminal Mechanical
Soldering Heat
Solderability
焊錫附著性
焊錫耐熱性
Resistance
端子強度
振動試驗
落下測試
Drop test
Vibration
Strength
Item
志豐電子股份有限公司 KINGSTATE ELECTRONICS CORP 3/5 KPEG623AN
Lead terminals are immersed in rosin for 5 seconds and then immersed
in solder bath of +270±5℃ for 3±1 seconds.
端子部份浸入松香溶液 5 秒後,再浸入+270±5℃溶融焊鍚槽中 3±1 秒.
Lead terminal are immersed up to 1.5mm from sounder’s body in solder
bath of +300±5℃ for 3± 0.5 seconds or +260±5℃ for 10±1 seconds.
距離端子根部1.5mm 的位置,浸入+300±5℃的焊鍚槽 3±0.5 秒,
或+260±5℃ 的焊錫槽10±1 秒.
The force 10 seconds of 9.8N (1.0kg) is applied to each terminal in axial
direction.
各端子的軸方向施以9.8N (1.0kg)的力量10 秒.
Buzzer shall be measured after being applied vibration of amplitude of
1.5mm with 10 to 55hz band of vibration frequency to each of 3
per-pendicular directions for 2 hours.
振動週波數 10∼55HZ、全振幅 1.5mm 於 X.Y.Z 3 個方向,各 2 小時.
The part only shall be dropped from a height of 75cm onto a 40mm thick
wooden board 3 times in 3 axes (X.Y.Z). (a total of 9 times).
單體從75 公分高處, X.Y.Z.3 個方向,各3 回,落於 40mm 厚木板上.
Test Condition
90% min. lead terminals shall be
wet with solder. (Except the
edge of terminal)
浸入端子部份附著焊鍚 90%以
上.(末端斷面不算)
No interference in operation
操作上無任何不良.
No damage and cutting off
端子不鬆動, 不脫落.
The value of oscillation
frequency/ current consumption
should be in 10% compared with
initial ones .The SPL should be
in ± 10dB compared with initial
one.
諧振頻率與消耗電流變化量須在
±10%內. 輸出音壓變化量須在
±10dB 內.
Evaluation standard