AXA2R63061P Panasonic Electric Works, AXA2R63061P Datasheet - Page 7

• Manufacturer Part Number: AXA2R63061P
• Description: CONN SD MEMORY CARD TYPE R SMD
• Manufacturer: Panasonic Electric Works
• Series: AXA2Rr

Specifications of AXA2R63061P

• Card Type: Secure Digital - SD
• Number Of Positions: 12 (9 + 3)
• Connector Type: Connector and Ejector
• Insertion, Removal Method: Push In, Push Out
• Mounting Type: Surface Mount, Right Angle
• Features: Board Guide, Switch
• Height Above Board: 0.134" (3.40mm)
• Mounting Feature: Normal, Standard - Top
• Contact Finish: Gold
• Contact Finish Thickness: Flash
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Ejector Side: -

EMBOSSED TAPE AND REEL
• Tape dimensions
NOTES
1.Regarding the design of PC board
patterns
Conduct the recommended foot pattern
design, in order to preserve the
mechanical strength of terminal solder
areas.
2. Regarding the socket mounting
1) When reflow soldering when the slider
is locked, heat will cause the slider to
deform and not work. Therefore, please
confirm that the slider lock is released
before mounting if you have inserted and
removed a card before soldering.
2) Be aware that during mounting,
external forces may be applied to the
connector contact surfaces and terminals
and cause deformations.
3. Soldering
1) Reflow soldering
(1) Screen-printing method is
recommended for cream solder printing.
(2) Use the recommended foot pattern for
cream solder printing (screen thickness:
0.12 mm).
(3) The metal mask opening ratio for the
COM contact (one) and NO contacts
(two) must be 75%.
(4) When applying the different thickness
of a screen, please consult us.
(5) The following diagram shows the
recommended reflow soldering
temperature profile.
The recommended conditions for the
reflow temperature profile
To be transferred to Honda Tsushin kogyo Co.,Ltd. from October 1, 2009
155 to 165°C
Temperature
250°C max.
Emboss
carrier tape
Top cover
tape
Preheating
60 to 120 sec.
Peak temperature
Time
180 to 200°C
Within 30 sec.
40.40
44.00
Socket for SD memory card
20.20
(1.75)
(6) Measure the temperature at the
connector surface.
(7) If the reverse side of the board
undergoes reflow soldering after the
socket is reflow-soldered, fix the socket
with tape or adhesive; otherwise, the
socket may drop. The socket can
withstand two iterations of reflow
soldering.
2) Hand soldering
• Set the soldering tip to 300°C, and
solder for no more than 5 seconds.
• Be aware that for the 0 mm standoff
type, solder creeping at the retention
solder tab sections may occur if soldering
is conducted for long periods or if too
much solder is used.
4. Cleaning after soldering
Inside the socket there is a slider section
and card detection contact/write
protection mechanism. If anything such
as flux remains inside after washing,
insertion and removal will be hampered
and contact will be faulty. Therefore, do
not use methods that involve submersion
when cleaning. (Partial cleaning of the
PC board and soldered terminals is
possible.)
5. After PC board mounting
1) Warping of the PC board should be no
more than 0.03 mm for the entire
connector length.
2) When assembling PC boards or
storing them in block assemblies, make
sure that undue weight is not exerted on
a stacked socket.
3) Be sure not to allow external pressure
to act on sockets when assembling PC
boards or moving in block assemblies.
6. Handling single components
1) Make sure not to drop or allow parts to
fall from work bench
(Unit: mm)
• Reel dimensions (Conforming to JIS C0806-1995)
(44.4)
+2
panasonic-electric-works.net/ac
0
Taping reel
2) Be cautious when handling because
excessive force applied to the terminals
will cause deformation and loss of
terminal coplanarity.
3) Repeated bending of the terminals
may break them.
7. Card fitting
1) These products are made for the
design of compact and lightweight
devices and therefore the molded part is
very thin. For this reason, design the
device to prevent undue wrenching forces
from being applied to the product during
use.
2) The sockets are constructed to prevent
reverse card insertion. Caution is
required because repeated, mistaken
reverse insertion may damage the socket
and card.
3) When not soldered, be careful not to
insert and remove the socket’s card.
Doing so will cause a decrease in
anchoring ability of the molded part and
loss of coplanarity.
4) Forcibly removing a fitted card may
degrade the card removal prevention
lock. To remove a card, be sure to push
the card in the insertion direction to
release the slider lock before pulling out
the card.
5) Please include notes to the following
effect in your user manuals.
6) The card ejection protection lock does
not work for MMC.
7) The socket does not have a wrong
insertion protection structure for MMC.
Be careful about the insertion direction.
8) If an MMC is inserted, it is possible
that a short circuit between the socket’s
signal contacts No. 7 and 8 and the
MMC’s contact No. 7 may be caused.
Top cover tape
Label
Cavity
Emboss carrier tape
Tape
AXA2R