F3SNA0307P25 Omron, F3SNA0307P25 Datasheet - Page 13

• Manufacturer Part Number: F3SNA0307P25
• Description: Safety Light Curtain
• Manufacturer: Omron

Specifications of F3SNA0307P25

• Beam Spacing: 15mm
• Control Output Type: PNP
• No. Of Beams: 19
• Protection Height: 307mm
• Sensing Range Max: 10m
• Supply Voltage Max: 24VDC
• Peak Reflow Compatible (260 C): No
• Light Curtain Type: Safety
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Connections
Wiring for Sensor Only Configuration
Wiring for the Manual Reset Mode and the EDM Function
Series Connection (Up to 3 Sets)
Using series connection models (model numbers ending in -01, -03,
-04, -05) enables series connection as shown in the figure at the right.
Either stand-alone models and the series connection models can be
used for the light curtains located at the top end.
Note: 1. To maintain performance characteristics, use the F39-
Emitter cable
F39-JC@A-L
2. The F3SN and F3SH cannot be connected in series.
3. Series connection is possible for model numbers ending in
(See
note 1.)
S1
JCR2B or the F39-JC3B to connect light curtains in series.
The F39-JC7B, F39-JC10B, or F39-JC15B cannot be
connected in series.
-04 or -05 (with 0.2 m cable with connectors).
Refer to page 2.
(See
note 1.)
S2
Emitter
http://www.ia.omron.com/
RS-485(A) (Gray)
RS-485(B) (Pink)
Receiver
K1
K2
K3
Receiver cable
F39-JC@A-D
K1
K2
+24 VDC
0 V
Power
supply
Wiring for the Auto-reset Mode
When the EDM is Not Used
When the EDM is not necessary
(1) Use the F39-MC11 to disable the EDM.
or
(2) Disable the EDM by changing the wiring as shown in the
Note: 1. Use very low load type switches.
S1:
S2:
S3:
K1, K2: Relay that control the dangerous zone, etc.
K3:
figure below, when the auxiliary output is Dark ON.
(c)Copyright OMRON Corporation 2007 All Rights Reserved.
Emitter
Emitter
Cable with Connectors
on Both Ends (for Emitter)
F39-JCR2B-L,
F39-JCR5B-L,
or
F39-JC3B-L
Cable with Connector
on One End
(for Emitter)
F39-JC@A-L
2. If K3 is not necessary, short-circuit the auxiliary
(See notes 1 and 3.)
External test switch
Interlock/lockout reset switch
Lockout reset switch (If the switch is not necessary,
connect between the reset input and +24 VDC.)
Load, PLC, etc. (used for monitoring)
(See
note 1.)
output with the EDM input.
S1
Emitter
(See
note 1.)
S3
F3SN-A/F3SN-B/F3SH-A
Receiver
F3SN-A@@@@P@@(-@@)*
Receiver
F3SN-A@@@@P@@-01
(or -03, -04, -05) *
Cable with Connectors
on Both Ends (for Receiver)
F39-JCR2B-D,
F39-JCR5B-D,
or
F39-JC3B-D
(See notes 1 and 3.)
Cable with Connector
on One End
(for Receiver)
F39-JC@A-D
(See note 2.)
Receiver
K3
K1
* Series connection is
possible for the F3SN-B.
13