HFE2 SAFTRONICS, HFE2 Datasheet

no-image

HFE2

Manufacturer Part Number
HFE2
Description
SOFTSTARTER, HFE2, 30A
Manufacturer
SAFTRONICS
Datasheet
1.HFE2.pdf (4 pages)

Specifications of HFE2

No. Of Phases
Single
Current Rating
30A
Approval Bodies
IEC 60947-4-2
External Depth
97.5mm
External Length / Height
228mm
External Width
135mm
Ip/nema
RoHS Compliant
For Use With
32A MCB Trip Characteristic Type "C"

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
HFE20-1/12-1HT-L2 (359)
Manufacturer:
TI
Quantity:
1 001
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
HFE20-1/5-1HST-L2(257)
Manufacturer:
RICHTEK
Quantity:
6 500
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
HFE200-250
Manufacturer:
TTI
Quantity:
23
Company:
HONG KONG JIETUO ZIJING INTERNATIONAL TRADING CO., LIMITED HONG KONG JIETUO ZIJING INTERNATIONAL TRADING CO., LIMITED
Part Number:
HFE2500-12
Quantity:
141
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
HFE2500-12/S
Manufacturer:
TDK-LAMBDA
Quantity:
86
Company:
HONG KONG JIETUO ZIJING INTERNATIONAL TRADING CO., LIMITED HONG KONG JIETUO ZIJING INTERNATIONAL TRADING CO., LIMITED
Part Number:
HFE2500-12/S
Quantity:
145
Company:
HONG KONG JIETUO ZIJING INTERNATIONAL TRADING CO., LIMITED HONG KONG JIETUO ZIJING INTERNATIONAL TRADING CO., LIMITED
Part Number:
HFE2500-24
Quantity:
142
Company:
Bonase Electronics (HK) Co., Limited Bonase Electronics (HK) Co., Limited
Part Number:
HFE2500-24/S
Manufacturer:
TDK-LAMBDA
Quantity:
86
Company:
HONG KONG JIETUO ZIJING INTERNATIONAL TRADING CO., LIMITED HONG KONG JIETUO ZIJING INTERNATIONAL TRADING CO., LIMITED
Part Number:
HFE2500-24/S
Quantity:
146
Company:
HONG KONG JIETUO ZIJING INTERNATIONAL TRADING CO., LIMITED HONG KONG JIETUO ZIJING INTERNATIONAL TRADING CO., LIMITED
Part Number:
HFE2500-32
Quantity:
143
APPLICATION
HFE Energy Saving soft starters are designed to
control single phase AC motors. Operation is fully
automatic, a low starting voltage is applied to the
motor as soon as the supply is switched on. The
internal automatic ramp control immediately takes
over and raises the voltage progressively, causing
the motor to accelerate smoothly.
At the end of the ramp period, the motor is operated
in Energy Saving mode and the HFE continuously
regulates the voltage to match mechanical load.
Energy consumption at light loads is reduced, motor
winding and case temperatures are lowered, motor
life is extended, noise levels are reduced and power
factor is improved.
The LED in the unit indicates when the unit is
ENERGY SAVING. As energy consumption is
reduced the ENERGY SAVING LED flashes at a
slower rate.
The HFE remains in circuit until the supply is
disconnected. The HFE automatically resets and is
ready for the next start.
Hfe
Digital Soft Starters
Safety at Work
It is the responsibility of the installer and user to ensure that this equipment is installed,
operated and maintained in accordance with the Health and Safety at Work Act in the
United Kingdom and all applicable legislation, regulations and codes of practice relevant to
your location.
Only qualified personnel should install this equipment, after first reading and understanding
this document. The installation instructions must be followed, and any questions or doubt
must be referred to the supplier of the equipment.
The system may be configured to allow for auto restart controlled from contacts on the
motor side of the unit. Users and operators must always take all necessary precautions to
prevent damage to equipment and especially to prevent the risk of injury to personnel
working on or near the motor and driven equipment.
The manufacturer does not assume any liability, express or implied, for any consequences
resulting from inappropriate, negligent or incorrect installation, application, use or adjust-
ment of the product or circuit design, or from mismatching of a soft starter to a motor.
HFE-2
ISOLATE FROM THE SUPPLY BEFORE WORKING ON THE UNIT OR MOTOR
30 Amp @ 110-230 Volts
page 1 M-2025-F 100401
F A I R F O R D
E L E C T R O N I C S
Soft Starters and Energy
Optimising Soft Starters

Related parts for HFE2

Image
Part Number
Description
Manufacturer
Datasheet
Request R
LIGHT ECO PLUS HID
Part Number:
LIGHT ECO PLUS HID
Description:
CONTROLLER, LIGHT, ECO HID
Manufacturer:
SAFTRONICS
Datasheet:
LIGHT_ECO_2.4.pdf (8 pages)

HFE2 Summary of contents

Page 1

... Hfe Digital Soft Starters HFE-2 30 Amp @ 110-230 Volts APPLICATION HFE Energy Saving soft starters are designed to control single phase AC motors. Operation is fully automatic, a low starting voltage is applied to the motor as soon as the supply is switched on. The internal automatic ramp control immediately takes over and raises the voltage progressively, causing the motor to accelerate smoothly ...

Page 2

Mechanical Details HFE-2 105 135 40.2 40 AWG mm 1.5- Three off Ø21mm holes for cable glands indicator Nm lbs-inch mm ...

Page 3

WIRING The soft starter is normally inserted into the circuit between the motor and whatever switchgear is normally used for isolation or switching. The unit can also be fitted before switchgear so that it can be installed in the supply ...

Page 4

... Rated insulation voltage: Rated impulse withstand voltage: Short circuit co–ordination: Fuse Type: Design standards: IEC 60947–4–2: “AC Semiconductor Motor Controllers and Starters”. Fairford Electronics Limited, Coombe Works, Derby Road, Kingsbridge, Devon TQ7 1JL, UK TEL (0) 1548 857494 EMAIL: sales@fairford.co.uk Document No ...

Related keywords