MTL5513 MTL SURGE TECHNOLOGIES, MTL5513 Datasheet

MTL5513

Manufacturer Part Number

MTL5513

Description

ISOLATED BARRIER, DIG I/P

Manufacturer

MTL SURGE TECHNOLOGIES

Datasheet

1.MTL5513.pdf (2 pages)

Specifications of MTL5513

Input Type

Proximity Detectors

Output Type

Transistor

Approval Bodies

ATEX

External Depth

123.6mm

External Length / Height

109.8mm

External Width

15.8mm

Isolation Input

Isolated

Mounting Type

DIN

Svhc

No SVHC (15-Dec-2010)

Rohs Compliant

Lead Free Status / RoHS Status

Current page: 1 of 2
Download datasheet (141Kb)

The MTL5513 enables two solid-state outputs in the safe area to

be controlled by two switches or proximity detectors located in the

hazardous area. The Ch1/Ch2 output transistors share a common

terminal and can switch +ve or -ve polarity signals. Independent output

phase reversal and line fault detection are enabled via switches for

each output. LFD indication is provided on the top of the module.

SPECIFICATION

See also common specification

Number of channels

Location of switches

Location of proximity detectors

Hazardous-area inputs

Voltage applied to sensor

Input/output characteristics

Line fault detection (LFD) (when selected)

Note: Resistors must be fitted when using the LFD facility with a contact input

500Ω to 1kΩ in series with switch

20kΩ to 25kΩ in parallel with switch

Phase reversal

Safe-area outputs

MTL5513 SWITCH/

PROXIMITY DETECTOR

INTERFACE

two-channel, with line fault detection

and phase reversal

Two

Zone 0, IIC, T6 hazardous area

Div. 1, Group A hazardous location

Zone 0, IIC, T4–6 hazardous area if suitably certified

Div. 1, Group A hazardous location

Inputs conforming to BS EN60947–5–6:2001 standards for

proximity detectors (NAMUR)

7 to 9V dc from 1kΩ ±10%

Normal phase

Hysteresis: 200µA (650Ω) nominal

User-selectable for each channel via switches on the side of the

unit. Line faults are indicated by an LED for each channel.

Open-circuit alarm on if Iin < 50µA

Open-circuit alarm off if Iin > 250µA

Short-circuit alarm on if Rin < 100Ω

Short-circuit alarm off if Rin > 360Ω

Independent for each channel, user-selectable

Floating solid-state outputs compatible with logic circuits

Operating frequency:

Max. off-state voltage:

Max. off-state leakage current:

Max. on-state resistance:

Max. on-state current:

Outputs closed if input > 2.1mA (< 2kΩ in input circuit)

Outputs open if input < 1.2mA (> 10kΩ in input circuit)

EUROPE (EMEA)

AMERICAS

ASIA PACIFIC

E-mail: enquiry@mtl-inst.com

Tel: +44 (0)1582 723633

Tel: +1 281 571 8065

Tel: +65 6 487 7887

Web site: www.mtl-inst.com

dc to 500Hz

± 35V

± 50µA

25Ω

± 50mA

Fax: +44 (0)1582 422283

Fax: +1 281 571 8069

Fax: +65 6 487 7997

The given data is only intended as a product description and should not be re-

garded as a legal warranty of properties or guarantee. In the interest of further

technical developments, we reserve the right to make design changes.

* Signal plug HAZ1-3 is required for access to this function

LED indicators

Maximum current consumption

Power dissipation within unit

Safety description (each channel)

Hazardous area

Terminal

Green: power indication

Yellow: two: channel status, on when outputs are on

Red: two: LFD indication, on when line fault detected

27mA at 24V

0.65W typical at 24V, with 10mA loads

0.78W max. with 50mA loads

=10.5V I

=14mA P

Function

Input –ve (Ch 1)

Input +ve (Ch 1)

To earth leakage detector*

Input –ve (Ch 2)

Input +ve (Ch 2)

To earth leakage detector*

Output (Ch 2)

Output (Ch 1/Ch 2)

Output (Ch 1)

Supply –ve

=37mW U

Safe area

= 253V rms or dc

EPS5513-2

Jan 2009

Related parts for MTL5513

MTL5513 Summary of contents

Page 1

... INTERFACE two-channel, with line fault detection and phase reversal The MTL5513 enables two solid-state outputs in the safe area to be controlled by two switches or proximity detectors located in the hazardous area. The Ch1/Ch2 output transistors share a common terminal and can switch +ve or -ve polarity signals. Independent output phase reversal and line fault detection are enabled via switches for each output ...

Page 2

MTL5500 SERIES COMMON SPECIFICATION Please go to our website at www.mtl-inst.com for the latest information regarding safety approvals, certificates and entity parameters. Connectors Each MTL5500 unit is supplied with signal connectors, as applicable. When using crimp ferrules for the hazardous ...

Related keywords

MTL5513 datasheet
MTL5513 data sheet
MTL5513 pdf datasheet
MTL5513 component
MTL5513 part
MTL5513 distributor
MTL5513 RoHS
MTL5513 datasheet download