10-4102 GC Electronics, 10-4102 Datasheet

10-4102

Manufacturer Part Number

10-4102

Description

Connector

Manufacturer

GC Electronics

Type

Cementr

Datasheet

1.10-4102.pdf (4 pages)

Specifications of 10-4102

Chemical Component

Toluene

Dispensing Method

Bottle

Primary Type

Thinner

Weight

2 fl.oz.

Lead Free Status / Rohs Status

RoHS Compliant part Hazardous Materials

Current page: 1 of 4
Download datasheet (374Kb)

CHEMICALS

Polystyrene Q-Dope

Thinner

For thinning polystyrene base coil dopes and

cements. Can also be used for cementing

polystyrene parts.

Part No. 10-4102

N.S.N. 8010-00-063-1376

N.S.N. 8040-00-902-1159

Radio-TV Cement

Solvent

Fast acting solvent formulated for use in

speaker repair. Dissolves cement on speaker

cones, spiders, frames, voice-coils. May also

be used as a thinner for all lacquer type

cements.

Part No. 10-312

Part No. 10-318

Part No. 10-320

N.S.N. 8010-00-775-5893

Part No. 10-321

Silver Print II

(Conductive Paint)

For PC repair or add-on circuit traces. Pure

silver in acrylic lacquer based carrier may

be brushed on for either conductors or

shielding. Connections have equal or better

conductivity than copper (0.1 ohms per

square).

Part No. 22-023

Part No. 22-024

Red Insulating Varnish

Alkyd-based compound, especially resistant

to environmental extremes including oils,

water and most acids and alkalis. Retains its

high dielectric strength even if wet and is,

therefore, especially adaptable to the

insulation of electrical and electronic

devices or components which may be

operated in a very humid climate and up to

250°F (121°C). For general insulation of

coils, transformers, motor windings and for

all-around protection against oxidation and

atmospheric attacks.

Part No. 10-9002

N.S.N. 5970-00-901-5331

Part No. 10-9002-1G

Part No. 10-9008

2 fl. oz. Bottle

8 fl. oz. Bottle

16 fl. oz. Bottle

1 gal. Can

All quantities are single; BU’s are packages of 10 Unless otherwise noted.

2 fl. oz. Bottle

1/2 troy oz. Bottle

1 troy oz. Bottle

2 fl. oz. Bottle w/Brush

1 gal. can

8 fl. oz. Bottle

Print Kote Conformal

Coating

The ultimate coating for PC boards provides

a protective shield to resist environmental

contaminants. Prevents arcing and shorting.

Air dry 15 to 30 minutes. May be baked at

200°C for 30-60 minutes for extreme high

temperature applications.

Part No. 22-203

N.S.N. 8010-00-711-2173

Nickel Print

(Conductive Paint)

A quick drying lacquer-based coating, pig-

mented with powdered nickel. For repair and

modification of printed circuits. Conductivity

is 5 to 6 ohms per square.

Part No. 22-207

THINNERS & SOLVENTS

Paint Thinner

All purpose mineral spirit type thinner and

solvent for paint and varnish base products.

Part No. 10-6702

N.S.N. 8010-00-054-1521

Print Kote Solvent

A solvent to remove silicone and other

types of protective coatings from PC boards.

Required when modifying PC boards or

replacing components where the protective

coating interferes with the desoldering and

resoldering operation.

Part No. 22-209

N.S.N. 6810-00-711-2185

2 fl. oz. Bottle

COATINGS

Related parts for 10-4102

10-4102 Summary of contents

Page 1

... CHEMICALS Polystyrene Q-Dope Thinner For thinning polystyrene base coil dopes and cements. Can also be used for cementing polystyrene parts. Part No. 10-4102 2 fl. oz. Bottle N.S.N. 8010-00-063-1376 N.S.N. 8040-00-902-1159 Radio-TV Cement Solvent Fast acting solvent formulated for use in speaker repair. Dissolves cement on speaker cones, spiders, frames, voice-coils ...

Page 2

... Warning: This product contains Toluene, a chemical known to the State of California to cause birth defects or other reproductive harm. Physical Description: Physical State: Appearance: Odor: Odor Threshold: Melting/Freezing Point: Boiling Point: Part Number(s): 10-4102 MATERIAL SAFETY DATA SHEET Section 1 - Identification of Product Least Slight 2 Moderate 3 High ...

Page 3

... Protective Equipment for Firefighters: Wear full protective clothing and self-contained breathing apparatus. Additional Advice: Hazardous Combustion Products: Emergency Overview: Routes of Exposure: Health Hazards: Part Number(s): 10-4102 1.2 – 8% (V) 100% Typical 28.5 mN C/68 F (ASTM D-971) Typical 871 kg/ C/59 F 3.1 mg/m3 Typical 1 kPa at 0 C/32 F Typical 3 – ...

Page 4

... DSL INV (CN) ENCS (JP) TSCA Part Number(s): 10-4102 Avoid contact with skin, eyes, and clothing. Extinguish any naked flames. Do not smoke. Remove ignition sources. Avoid sparks. Electrostatic charges may be generated during pumping. Electrostatic discharge may cause fire. Ensure electrical continuity by bonding and grounding (earthing) all equipment. Restrict line velocity during pumping in order to avoid generation of electrostatic discharge (< ...

Related keywords

10-4102 datasheet
10-4102 data sheet
10-4102 pdf datasheet
10-4102 component
10-4102 part
10-4102 distributor
10-4102 RoHS
10-4102 datasheet download