44828-1162 Molex Inc, 44828-1162 Datasheet
44828-1162
Specifications of 44828-1162
044828-1162-C
0448281162
0448281162-C
44828-1162-C
448281162
448281162-C
WM17127TR
Available stocks
Related parts for 44828-1162
44828-1162 Summary of contents
Page 1
... PRELIMINARY HANDYLINK™ APPLICATION SPECIFICATION 44828 SMT Receptacle Connector 45339 and 45593 Plug Connector Modules REVISION: ECR/ECN INFORMATION: EC No: UCP2004-2588 A 6/24/04 DATE: DOCUMENT NUMBER: AS-44828-001 HANDYLINK™ I/O CONNECTORS 45560 SMT Cradle Connector TITLE: APPLICATION SPECIFICATION HANDYLINK™I/O CONNECTOR SYSTEM CREATED / REVISED BY: CHECKED BY: T ...
Page 2
... Mating and Un-Mating of Connectors 4.1 Recommendations for Mating and Un-Mating 4.2 Mating Alignment Tolerances 5.0 Soldering Process Recommendations 5.1 44828 SMT Receptacle Connector 5.1.1 PCB Layout 5.1.2 Solder Paste Stencil Layout 5.1.3 Reflow Profile 5.1.4 Inspection 5.2 45560 SMT Cradle Connector 5 ...
Page 3
... Plug Connector Modules Series 45339 (Wire Termination) Series 45593 (PCB Termination) 2.2 Dimensions, Materials, Platings, and Markings (See applicable sales drawings for information) 3.0 APPLICABLE DOCUMENTS AND SPECIFICATIONS Product Specification PS-44828-001 Sales Drawing SD-44828-162 Sales Drawing SD-45560-160, SD-45560-161, SD-45560-162 Sales Drawing ...
Page 4
... Mating Alignment Tolerances 4.2.a 44828 Receptacle to 45339 or 45593 Plug Connectors The HandyLink™ plug and receptacle have been appropriately designed and toleranced to be mated and unmated by hand. The connectors’ alignment features are manufactured with clearances to allow axial mating mis-alignment, as illustrated in the Figure 1, below: Figure 1 ...
Page 5
... APPLICATION SPECIFICATION 4.2 Mating Alignment Tolerances (continued) 4.2.b 44828 Receptacle to 45560 Cradle Connectors The HandyLink™ receptacle and cradle connectors’ alignment features are manufactured with clearances to allow some axial mating mis-alignment as illustrated in the Figure 2, below: Figure 2. Receptacle to Cradle Connector Axial Alignment (units: mm) NOTE: Mating misalignment may significantly influence the long-term durability of the connectors ...
Page 6
... See Sales Drawing for solderable surfaces. Contact Molex if further assistance is required. 5.1.3 Reflow Profile While the production solder reflow profile is typically established by the customer, based on their specific application, generic reflow profiles can be found in Product Specification PS-44828-001. The profiles are provided for reference purposes only. 5.1.4 Inspection Solder joints should be inspected using established conventional methods ...
Page 7
... See the applicable Sales Drawing for an illustration of the recommended PCB hole layout. 5.4.2 Inspection Solder joints should be inspected using established conventional methods REVISION: ECR/ECN INFORMATION: EC No: UCP2004-2588 A 6/24/04 DATE: DOCUMENT NUMBER: AS-44828-001 TITLE: APPLICATION SPECIFICATION HANDYLINK™I/O CONNECTOR SYSTEM CREATED / REVISED BY: CHECKED BY: T. Gregori/ M. Simmel Marc Simmel . . SHEET No. ...
Page 8
... Wherever possible, the 0.10 maximum clearance condition with the receptacle should be minimized by utilizing a clam-shell style package design. REVISION: ECR/ECN INFORMATION: EC No: UCP2004-2588 A 6/24/04 DATE: DOCUMENT NUMBER: AS-44828-001 (units: mm) TITLE: APPLICATION SPECIFICATION HANDYLINK™I/O CONNECTOR SYSTEM CREATED / REVISED BY: CHECKED BY: T. Gregori/ M. Simmel Marc Simmel SHEET No. ...
Page 9
... Please refer to section 6.4.2 for further details concerning cradle design recommendations. REVISION: ECR/ECN INFORMATION: EC No: UCP2004-2588 A 6/24/04 DATE: DOCUMENT NUMBER: AS-44828-001 TITLE: APPLICATION SPECIFICATION HANDYLINK™I/O CONNECTOR SYSTEM CREATED / REVISED BY: CHECKED BY: T. Gregori/ M. Simmel Marc Simmel SHEET No. 9 ...
Page 10
... Figure 4. Sealing to achieve ingress protection with the receptacle connector REVISION: ECR/ECN INFORMATION: EC No: UCP2004-2588 A 6/24/04 DATE: DOCUMENT NUMBER: AS-44828-001 Gaskets may be applied to the top and sides, or front surfaces. The bottom surface, once soldered, forms a continuous seal with the PCB TITLE: APPLICATION SPECIFICATION HANDYLINK™I/O CONNECTOR SYSTEM CREATED / REVISED BY: CHECKED BY: T ...
Page 11
... Dressing of the wires should be avoided until after the soldering and encapsulation processes are complete. REVISION: ECR/ECN INFORMATION: EC No: UCP2004-2588 A 6/24/04 DATE: DOCUMENT NUMBER: AS-44828-001 Wire soldertails (2 rows) Cavities under the latches (2 places) TITLE: APPLICATION SPECIFICATION HANDYLINK™I/O CONNECTOR SYSTEM CREATED / REVISED BY: CHECKED BY: T. Gregori/ M. Simmel Marc Simmel Figure 6 ...
Page 12
... Omission of this step would allow the final over-mold resin to extrude into cavities in the housing that could disable latch and terminal function. REVISION: ECR/ECN INFORMATION: EC No: UCP2004-2588 A 6/24/04 DATE: DOCUMENT NUMBER: AS-44828-001 TITLE: APPLICATION SPECIFICATION HANDYLINK™I/O CONNECTOR SYSTEM CREATED / REVISED BY: CHECKED BY: T. Gregori/ M. Simmel Marc Simmel Figure 7. Encapsulated plug connector Figure 8 ...
Page 13
... Please see Section 6.4.1 for a discussion of design best practices for the over-mold. REVISION: ECR/ECN INFORMATION: EC No: UCP2004-2588 A 6/24/04 DATE: DOCUMENT NUMBER: AS-44828-001 TITLE: APPLICATION SPECIFICATION HANDYLINK™I/O CONNECTOR SYSTEM CREATED / REVISED BY: CHECKED BY: T. Gregori/ M. Simmel Marc Simmel Figure 9. Crimp barrel installed Figure 10 ...
Page 14
... There is significant risk of the end users pulling at connections in off-axis directions. Figure 11. Example of an application with a great degree of curvature near the connector interface. REVISION: ECR/ECN INFORMATION: EC No: UCP2004-2588 A 6/24/04 DATE: DOCUMENT NUMBER: AS-44828-001 TITLE: APPLICATION SPECIFICATION HANDYLINK™I/O CONNECTOR SYSTEM CREATED / REVISED BY: CHECKED BY: T. Gregori/ M. Simmel Marc Simmel SHEET No ...
Page 15
... This type of design will provide support for the end-user to hold the product by the connector or where a heavy or stiff accessory cable is used. REVISION: ECR/ECN INFORMATION: EC No: UCP2004-2588 A 6/24/04 DATE: DOCUMENT NUMBER: AS-44828-001 Surfaces are contoured to mimic the end product TITLE: APPLICATION SPECIFICATION HANDYLINK™I/O CONNECTOR SYSTEM CREATED / REVISED BY: CHECKED BY: T. Gregori/ M. Simmel Marc Simmel Over-molded lip SHEET No ...
Page 16
... If this is not achieved, excessive wear between the connector housings and/or electrical discontinuities may occur. REVISION: ECR/ECN INFORMATION: EC No: UCP2004-2588 A 6/24/04 DATE: DOCUMENT NUMBER: AS-44828-001 External latching feature (each side) Guide ribs (each side) TITLE: APPLICATION SPECIFICATION HANDYLINK™I/O CONNECTOR SYSTEM CREATED / REVISED BY: CHECKED BY: T. Gregori/ M. Simmel Marc Simmel SHEET No ...
Page 17
... NOTE: For details about mounting the connectors to the PCB and the use of fasteners, please refer to the applicable Sales Drawings. REVISION: ECR/ECN INFORMATION: EC No: UCP2004-2588 A 6/24/04 DATE: DOCUMENT NUMBER: AS-44828-001 TITLE: APPLICATION SPECIFICATION HANDYLINK™I/O CONNECTOR SYSTEM CREATED / REVISED BY: CHECKED BY: T. Gregori/ M. Simmel Marc Simmel Guide Rails (each side) ...
Page 18
... Figure 17 shows a chamfer detail applicable to 45593. Figure 15. Cradle Detail (45560) (units: mm) REVISION: ECR/ECN INFORMATION: EC No: UCP2004-2588 A 6/24/04 DATE: DOCUMENT NUMBER: AS-44828-001 Figure 16. Cradle Detail (45593) Figure 17. Detail from Figure 16. (units: mm) TITLE: APPLICATION SPECIFICATION HANDYLINK™I/O CONNECTOR SYSTEM CREATED / REVISED BY: CHECKED BY: T. Gregori/ M. Simmel Marc Simmel (units: mm) SHEET No ...
Page 19
... NOTE: For details about mounting the connectors to the PCB and the use of fasteners, please refer to the applicable Sales Drawings. REVISION: ECR/ECN INFORMATION: EC No: UCP2004-2588 A 6/24/04 DATE: DOCUMENT NUMBER: AS-44828-001 Disconnect ‘Rocking’ Direction Figure 18. Shelf-Style Cradle Features TITLE: APPLICATION SPECIFICATION HANDYLINK™I/O CONNECTOR SYSTEM CREATED / REVISED BY: T. Gregori/ M. Simmel ...
Page 20
... REVISION: ECR/ECN INFORMATION: EC No: UCP2004-2588 A 6/24/04 DATE: DOCUMENT NUMBER: AS-44828-001 BACK SUPPORT (REQUIRED) Figure 20. Section View of Shelf- Style Cradle (units: mm) Rocking Direction NOTE: Orientation of the receptacle connector and the plug or cradle connector must correspond to that shown for good operation of a ‘rocking’ design. ...
Page 21
... Electrical Recommendations 7.1 Power Considerations Please see the Product Specification, PS-44828-001, for the nominal electrical specifications. For applications where the sustained electrical power usage requirements exceed the limits stated in the product specification, the use of multiple circuits is suggested. When the end-application is likely to encounter salt spray conditions, potential differences exceeding 4VDC should be separated by more than one terminal position (i ...