45593-1600 Molex Inc, 45593-1600 Datasheet
45593-1600
Specifications of 45593-1600
045593-1600-E
0455931600
0455931600-E
45593-1600-E
455931600
455931600-E
WM17126
Available stocks
Related parts for 45593-1600
45593-1600 Summary of contents
Page 1
... PRELIMINARY HANDYLINK™ APPLICATION SPECIFICATION 44828 SMT Receptacle Connector 45339 and 45593 Plug Connector Modules REVISION: ECR/ECN INFORMATION: EC No: UCP2004-2588 A 6/24/04 DATE: DOCUMENT NUMBER: AS-44828-001 HANDYLINK™ I/O CONNECTORS 45560 SMT Cradle Connector TITLE: APPLICATION SPECIFICATION HANDYLINK™I/O CONNECTOR SYSTEM CREATED / REVISED BY: CHECKED BY: T ...
Page 2
... Reflow Profile 5.2.4 Inspection 5.3 45339 Plug Module for Wire Termination 5.3.1 Applicable Wire Sizes 5.3.2 Wire Preparation 5.3.3 Inspection 5.4 45593 Plug Module for PCB Termination 5.4.1 PCB Layout 5.4.2 Inspection 6.0 Mechanical Design Recommendations 6.1 Mechanical Fasteners and Support 6 ...
Page 3
... SMT Cradle Connectors Series 45560 (Perpendicular and Parallel Mating) Plug Connector Modules Series 45339 (Wire Termination) Series 45593 (PCB Termination) 2.2 Dimensions, Materials, Platings, and Markings (See applicable sales drawings for information) 3.0 APPLICABLE DOCUMENTS AND SPECIFICATIONS Product Specification PS-44828-001 ...
Page 4
... Mating Alignment Tolerances 4.2.a 44828 Receptacle to 45339 or 45593 Plug Connectors The HandyLink™ plug and receptacle have been appropriately designed and toleranced to be mated and unmated by hand. The connectors’ alignment features are manufactured with clearances to allow axial mating mis-alignment, as illustrated in the Figure 1, below: Figure 1 ...
Page 5
PRELIMINARY HANDYLINK™ APPLICATION SPECIFICATION 4.2 Mating Alignment Tolerances (continued) 4.2.b 44828 Receptacle to 45560 Cradle Connectors The HandyLink™ receptacle and cradle connectors’ alignment features are manufactured with clearances to allow some axial mating mis-alignment as illustrated in the Figure 2, ...
Page 6
PRELIMINARY HANDYLINK™ APPLICATION SPECIFICATION 5.0 SOLDERING PROCESS RECOMMENDATIONS 5.1 44828 SMT Receptacle Connector 5.1.1 PCB Layout See the applicable Sales Drawing for an illustration of the recommended PCB layout. Contact Molex if further assistance is required. 5.1.2 Solder Paste Stencil ...
Page 7
... Pre-tinning is recommended. 5.3.3 Inspection Solder joints should be inspected using established conventional methods 5.4 45593 Plug Module for PCB Termination 5.4.1 PCB Layout See the applicable Sales Drawing for an illustration of the recommended PCB hole layout. 5.4.2 Inspection Solder joints should be inspected using established conventional methods ...
Page 8
PRELIMINARY HANDYLINK™ APPLICATION SPECIFICATION 6.0 MECHANICAL MOUNTING RECOMMENDATIONS 6.1 Mechanical Fasteners and Support 6.1.1 Receptacle Connector Molex recommends that the receptacle connector be mounted within the end-application enclosure such that it is recessed by 1.6 to 2.4mm from the outermost ...
Page 9
... Plug Connector Module The plug connector module is intended to be used as a part of a assembly using either direct wire soldering (45339) or using an intermediary PCB (45593). Overmolding and/or clam shell style covers must be used to protect the wire connections and the appropriate service loops and wire strain reliefs must be incorporated in a cable assembly to prevent damage during use ...
Page 10
PRELIMINARY HANDYLINK™ APPLICATION SPECIFICATION 6.2 Ingress Protection Ingress protection, as described by IEC 60529 function of the customer’s enclosure. The HandyLink™ Receptacle Connector has been designed to facilitate enclosure design when ingress protection is required. The interfaces between ...
Page 11
... Wire Soldering This section provides an outline of the recommended plug cable over-molding practices for the 45339 and 45593 plug connector modules. The 45339 connector (a 16-circuit wire termination version) is shown, below, prior to soldering. Please note the following features: Latch soldertails (2 places) Figure 5. Soldertail side of the plug connector ...
Page 12
PRELIMINARY HANDYLINK™ APPLICATION SPECIFICATION 6.3.2 Encapsulation The next step after soldering is to pre-seal or encapsulate the back end of the connector and hold the wires in place using a silicone sealant or a low-pressure Macro-melt polyamide adhesive molding. The ...
Page 13
PRELIMINARY HANDYLINK™ APPLICATION SPECIFICATION 6.3.3 Strain Relief Molex strongly recommends the use of a crimp barrel or ferrule over the wire bundle (including ground or drain wire) that also captures the cable jacket and tension member, if used. This will ...
Page 14
PRELIMINARY HANDYLINK™ APPLICATION SPECIFICATION 6.4 Design Best Practices The information provided so far in this document has been related to the basic usage conditions of the HandyLink™ connectors. The following sections contain important information and guidelines for design that apply ...
Page 15
PRELIMINARY HANDYLINK™ APPLICATION SPECIFICATION Supplemental guide features may be incorporated into or complement the over-mold design as illustrated in Figures 12 and 13: o Contouring with a Lip To provide mechanical support for torque out of the axial plane of ...
Page 16
PRELIMINARY HANDYLINK™ APPLICATION SPECIFICATION o Supplemental Latching and Alignment Posts Where the mass of the end product is greater than 1000 grams and is subject to sudden accelerations or strong vibrations during use, a cup-style receptacle needs to be considered ...
Page 17
PRELIMINARY HANDYLINK™ APPLICATION SPECIFICATION 6.4.2 Cradle Designs o Cup Style The cup or holster style of cradle provides the greatest degree of alignment between mating connectors. Where the end product mass is greater than 1000 grams the use of supplemental ...
Page 18
... PRELIMINARY HANDYLINK™ APPLICATION SPECIFICATION Figures 15 and 16 show orthogonal views of showing differences in the position and size of the openings in the cradle casing, and the PCB location for the 45560 and 45593 connectors. Figure 17 shows a chamfer detail applicable to 45593. Figure 15. Cradle Detail (45560) ...
Page 19
PRELIMINARY HANDYLINK™ APPLICATION SPECIFICATION o Shelf Style To achieve a ‘rocking’ disconnection for the end product from the cradle, a shelf style cradle design may be used under the following conditions: Ø No supplemental guide posts may be used; Ø ...
Page 20
... In addition to the differences in the position and size of the openings in the cradle casing, the PCB location for the 45560 and 45593 connectors, and the chamfer detail applicable to 45593 that is shown in Figures 15 thru 17. Figures 19 through 21 illustrate details necessary to achieve a good ‘rocking’ design. ...
Page 21
PRELIMINARY HANDYLINK™ APPLICATION SPECIFICATION 7.0 Electrical Recommendations 7.1 Power Considerations Please see the Product Specification, PS-44828-001, for the nominal electrical specifications. For applications where the sustained electrical power usage requirements exceed the limits stated in the product specification, the use ...