PXE2024WD05 TDK Corporation, PXE2024WD05 Datasheet - Page 3

• Manufacturer Part Number: PXE2024WD05
• Description: LAMBDA PART
• Manufacturer: TDK Corporation
• Series: PXEr
• Type: Point of Load (POL) Non-Isolated with Remote On/Offr

Specifications of PXE2024WD05

• Rohs Compliant: YES
• Output: ±5V
• Number Of Outputs: 2
• Power (watts): 20W
• Mounting Type: Through Hole
• Voltage - Input: 9 ~ 36V
• Package / Case: 8-DIP Module
• 1st Output: 5 VDC @ 2A
• 2nd Output: -5 VDC @ 2A
• Size / Dimension: 2.00" L x 1.60" W x 0.40" H (50.8mm x 40.6mm x 8.6mm)
• Power (watts) - Rated: 20W
• Operating Temperature: -40°C ~ 100°C
• Efficiency: 79%
• Approvals: CE, CSA, EN, UL
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 285-1524; PXE20-24WD05

Positive Logic
The power module operates in a
variety of thermal environments;
however, sufficient cooling
should be provided to help
ensure reliable operation of the
unit. Heat is removed by
conduction, convention, and
radiation to the surrounding
environment. Proper cooling can
be verified by measuring the
case temperature. The case
temperature (Tc) should be
measured at the position indicated in figure to the right.
When operating the module, adequate cooling must be provided
to maintain the case temperature at or below 100°C. Maintaining
a lower temperature will yield higher reliability of the device.
Optimum cooling is obtained with forced convection.
To turn the module on and off, the user must supply a switch (or
equivalent circuit below) to control the voltage between the on/off
terminal V
Power Supply On:
Power Supply Off:
Below are five possible circuits for driving the ON/OFF Pin:
Thermal Consideration
TTL/
CMOS
Opto Isolated Remote On/Off
on/off
5V
and the V
Open Collector Remote On/Off
Vin (-)
Open circuit or logic high (3.5-12V)
Closed circuit or logic low (<1.2V)
On/Off Control
i(-)
Vin (-)
On/Off Control
input terminal.
3055 Del Sol Blvd • San Diego, CA 92154 • 1-800-LAMBDA-4
(Permanently Disabled)
(Permanently Enabled)
TRIM
(+) Vout
Common
(-) Vout
Positive Logic
Positive Logic
On/Off Control
Vin (-)
On/Off Control
On/Off Control
Vin (-)
Vin (-)
Top View
(+) Vin
(-) Vin
CTRL
Installation Data Sheet
External Trim (output voltage
adjustment)
Output voltage set point adjustment allows the user to increase or
decrease the output voltage set point of a module. This is
accomplished by connecting an external resistor between the TRIM
pin and either the (+)Vout or (-)Vout pins. With an external resistor
between the TRIM and (+)Vout pin, the output voltage set point
decreases. With an external resistor between the TRIM and (-)Vout
pin, the output voltage set point increases.
See the following pages for values.
Thermal Resistance vs. Airflow
Flow Rate
Convection*
100LFM
200LFM
300LFM
400LFM
500LFM
Heatsink**
* Mounted vertically
** Optional heatsink 7G0011A (includes adhesive pad)
12.9
10.56
Θ Θ
8.22
6.69
5.09
4.86
8.24
°C/W