Q6008DH3TP Littelfuse Inc, Q6008DH3TP Datasheet - Page 5

• Manufacturer Part Number: Q6008DH3TP
• Description: Triac
• Manufacturer: Littelfuse Inc

Specifications of Q6008DH3TP

• Peak Reflow Compatible (260 C): Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Data Sheets
Electrical Specification Notes
(1) For either polarity of MT2 with reference to MT1 terminal
(2) For either polarity of gate voltage (V
(3) See Gate Characteristics and Definition of Quadrants.
(4) See Figure E2.1 through Figure E2.7 for current rating at specific
(5) See Figure E2.8 through Figure E2.10 for i
(6) See Figure E2.12 for V
(7) See Figure E2.11 for I
(8) See Figure E2.14 for I
(9) See Figure E2.13 for surge rating with specific durations.
(10) See Figure E2.15 for t
(11) See package outlines for lead form configurations. When ordering
(12) Initial on-state current = 200 mA dc for 0.8 A to10 A devices,
(13) See Figure E2.1 through Figure E2.6 for maximum allowable case
(14) Pulse width ≤10
©2004 Littelfuse, Inc.
Thyristor Product Catalog
T
C
(1) (5)
V
Volts
MAX
terminal
operating temperature.
special lead forming, add type number as suffix to part number.
400 mA dc for 15 A to 35 A devices
temperature at maximum rated current.
= 25 °C
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.8
1.8
1.8
1.8
1.8
1.4
1.4
1.5
1.5
TM
T
(2) (6) (15)
(18) (19)
C
MAX
Volts
V
= 25 °C
2.75
2.75
2.75
2.75
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
GT
µ
s;
I
GT
(1) (8) (12)
GT
H
gt
mAmps
GT
versus T
≤ I
MAX
versus I
100
100
100
100
100
versus T
35
35
35
35
35
50
50
50
50
50
70
70
70
70
70
50
50
50
50
I
versus T
H
GTM
GT
C
C
.
.
C
.
Amps
I
(14)
GTM
.
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
1.8
GT
2
2
2
2
2
2
2
2
2
2
2
2
2
2
) with reference to MT1
T
versus v
Watts
P
(14)
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
GM
T
.
P
Watts
G(AV)
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
E2 - 5
60/50 Hz
120/100
120/100
120/100
120/100
120/100
120/100
120/100
120/100
120/100
120/100
200/167
200/167
200/167
200/167
200/167
200/167
200/167
200/167
200/167
200/167
250/220
250/220
350/300
350/300
(9) (13)
Amps
I
TSM
(15) R
(16) T
(17) I
(18) Quadrants I, II, III only
(19) Minimum non-trigger V
Gate Characteristics
Teccor triacs may be turned on between gate and MT1 terminals
in the following ways:
•
•
In-phase signals (with standard AC line) using Quadrants I
and III
Application of unipolar pulses (gate always positive or nega-
tive), using Quadrants II and III with negative gate pulses and
Quadrants I and IV with positive gate pulses
However, due to higher gate requirements for Quadrant IV, it
is recommended that only negative pulses be applied. If pos-
itive pulses are required, see “Sensitive Triacs” section of
this catalog or contact the factory. Also, see
Figure AN1002.8, “Amplified Gate” Thyristor Circuit.
MAX QIV devices which are 0.2 V at 110 °C.
GT
(1) (4) (13)
Volts/µSec
C
L
dv/dt(c)
= 60 Ω for 0.8 A to10 A triacs; R
= T
= 300 mA for 25 A and 35 A devices
TYP
2
2
2
2
2
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
J
for test conditions in off state
100 °C
T
150
150
100
350
350
300
250
150
400
400
350
300
200
400
400
350
300
200
550
450
550
450
75
50
C
Volts/µSec
=
dv/dt
MIN
(1)
125 °C
GT
T
225
225
200
175
275
275
225
200
275
275
225
200
475
400
475
400
C
at 125 °C is 0.2 V for all except 50 mA
=
(10) (17)
µSec
TYP
t
L
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
3
3
3
3
gt
= 30 Ω for 15 A to 35 A triacs
http://www.littelfuse.com
Amps
166
166
166
166
166
166
166
166
166
166
260
260
508
508
I
60
60
60
60
60
60
60
60
60
60
2
t
2
Sec Amps/µSec
[phone]
di/dt
100
100
100
100
100
100
100
100
100
100
100
100
100
100
70
70
70
70
70
70
70
70
70
70
Triacs