FT3-HMB1-LL01-H FRAEN, FT3-HMB1-LL01-H Datasheet
FT3-HMB1-LL01-H
Specifications of FT3-HMB1-LL01-H
Related parts for FT3-HMB1-LL01-H
FT3-HMB1-LL01-H Summary of contents
Page 1
... High efficiency Available in 3 different beams 50mm diameter, sized for MR16 lamp appli cations Patent Pending The FT3 series Tri-lens are available for both B atwing and L ambertian Luxeon Lumileds (1). A software-optimized aspheric profile combined with front shaped micro-lens arrays enable the ...
Page 2
... General Characteristics _ _______________________________________________________________ Lens Material Holder Material Operating Temperature range S torage Temperature range Average transmittance in visible thick Optical Grade PMMA. _______________________________________________________________________ 01/04/2005 Optical Grade PMMA PC ABS or Transparent -40deg deg C -40deg deg C ectrum (400 – 700nm) >90%, as measured using 2/9 PC FT3 series lenses ...
Page 3
... Type of lens FT3-HNB1-Lbyy-H Narrow beam FT3-HMB1-Lbyy-H Medium beam FT3-HWB1-Lbyy-H Wide beam (3) The typical divergence varies with LED color due to different chip size and chip position tolerance. The typical total divergence is the full angle measured where the luminous intensity is half of the peak value. ...
Page 4
... Red White Warm LEDs LEDs White LEDs 32.6 28.4 13.5 4.2 5.7 4.1 1.3 1.6 1.6 Orange Red White LEDs LEDs LEDs 16.5 16.5 17.1 4.4 4.4 5.6 1.2 1.2 1 where (I) FT3 series lenses ...
Page 5
... Sets the lenses at the right position on the LEDs to provide best efficiency. Please note that flow lines and weld lines on the external surfaces of the lenses are acceptable if the optical performance of the lens is within the specification described in the section “OPTICAL CHARACTERISTS”. _______________________________________________________________________ 01/04/2005 5/9 FT3 series lenses ...
Page 6
... Mechanical Characteristics ________________________________________________________________ Lens + holder assembly view: _______________________________________________________________________ 01/04/2005 Lens (narrow beam shown) Holder (always included) Luxeon I Star Batwing LEDs shown PCB or heat sink with holes to heat stake the holder legs 6/9 Luxeon I Emitter Lambertian LEDs shown FT3 series lenses ...
Page 7
... Luxeon III or V Star Dimensions tolerance is +/-0.2mm _______________________________________________________________________ 01/04/2005 Shape of cutout in holder identifies the specific holder and application (Luxeon I Star, Luxeon III or V Star, or Emitter). Bottom of the holder 7/9 FT3 series lenses A B 26.2mm 22,5mm 26.2mm 22mm 26.7mm 23.3mm 26.7mm 22.7mm ...
Page 8
... The outer geometry of all the Tri-lenses (Narrow, Medium and Wide beam) are the same for the different beams, except the top of the lens. The lens can be identified by the top view: Top views (either Batwing or Lambertian): Narrow beam lens _______________________________________________________________________ 01/04/2005 Medium beam lens 8/9 Wide beam lens FT3 series lenses ...
Page 9
... LB01: Luxeon I Batwing Star/Emitter LBSW: Luxeon I Batwing Star Warm White LL01: Luxeon I Lambertian Star/Emitter and Luxeon III/V Emitter LLS3: Luxeon III/V Lambertian Star LENS TYPE: HNB1: Narrow beam lens HMB1: Medium beam lens HWB1: Wide beam lens 9/9 FT3 series lenses ...