ACPL-P456-020E Avago Technologies US Inc., ACPL-P456-020E Datasheet
ACPL-P456-020E
Specifications of ACPL-P456-020E
Related parts for ACPL-P456-020E
ACPL-P456-020E Summary of contents
Page 1
... Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxE denotes a lead-free product Description The ACPL-P456 and ACPL-W456 contain a GaAsP LED optically coupled to an integrated high gain photo detector. Minimized propagation between devices make these optocouplers excellent solutions for improving inverter efficiency through reduced switching dead time ...
Page 2
... Ordering Information ACPL-P456 and ACPL-W456 are UL Recognized with 3750 Vrms (5000 Vrms for ACPL-W456) for 1 minute per UL1577 and are approved under CSA Component Accep tance Notice #5, File CA 88324. Option Part number RoHS Compliant -000E -500E ACPL-P456 ACPL-W456 -060E -560E To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry ...
Page 3
... Recommended Pb-Free IR Profile Recommended reflow condition as per JEDEC Standard, J-STD-020 (latest revision). Non-Halide Flux should be used. Regulatory Information The ACPL-P456 and ACPL-W456 are approved by the following organizations: IEC/EN/DIN EN 60747-5-5 (Option 060 only) Approved with Maximum Working Insulation Voltage V = 1140 Vpeak (ACPL-W456) and V IORM (ACPL-P456) ...
Page 4
... Table 1. IEC/EN/DIN EN 60747-5-5 Insulation Characteristics* (ACPL-P456/W456 Option 060) Description Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤ 150 Vrms for rated mains voltage ≤ 300 Vrms for rated mains voltage ≤ 450 Vrms for rated mains voltage ≤ 600 Vrms for rated mains voltage ≤ ...
Page 5
Table 3. Absolute Maximum Ratings Parameter Storage Temperature Operating Temperature Average Input Current Peak Input Current (50% duty cycle, <1 ms pulse width) Peak Transient Input Current (<1 μs pulse width, 300 pps) Reverse Input Voltage (Pin 3-1) Average Output ...
Page 6
... Device considered a two-terminal device: Pins 1 and 3 shorted together and Pins 4, 5 and 6 shorted together accordance with UL1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 V current limit, I ≤ 5 μA) ; each optocoupler under ACPL-W456 is proof tested by applying an insulation test voltage ≥ 6000 V I-O (leakage detection current limit, I ≤ ...
Page 7
– FORWARD CURRENT – Figure 1. Typical Transfer Characteristics ...
Page 8
SHIELD 1500V CM Figure 6. CMR Test Circuit and Waveforms. 500 100 pF L 400 ...
Page 9
... Without a detector shield, the dominant cause of opto- coupler CMR failure is capacitive coupling from the input side of the optocoupler, through the package, to the detector IC as shown in Figure 13. The ACPL-P456/W456 improve CMR performance by using a detector IC with an optically transparent Faraday shield, which diverts the capacitively coupled current away from the sensitive IC circuitry ...
Page 10
I * TOTAL I I CLEDP 1 CLED01 300 Ω LED01 SHIELD SHIELD LEDN * THE ARROWS INDICATE THE DIRECTION OF CURRENT FLOW DURING + dV / Figure 16. AC Equivalent ...
Page 11
... This delay is the maximum value for the propaga- tion delay difference specification which is specified at 450 ns for the ACPL-P456/W456 over an operating tem- perature range of -40°C to 100°C. Delaying the LED signal by the maximum propagation ...
Page 12
I LED1 OUT1 V OUT2 Q2 OFF I LED2 t PLH MAX. t PHL MIN. PDD* MAX PLH- PHL MAX. = *PDD = PROPAGATION DELAY DIFFERENCE NOTE: THE PROPAGATION DELAYS USED TO CALCULATE ...