ACPM-7372-BLK Avago Technologies US Inc., ACPM-7372-BLK Datasheet
ACPM-7372-BLK
Specifications of ACPM-7372-BLK
Related parts for ACPM-7372-BLK
ACPM-7372-BLK Summary of contents
Page 1
... ACPM-7372 UMTS Band8 (880-915MHz) 4x4 Power Amplifier Module Data Sheet Description The ACPM-7372 is a fully matched 10-pin surface mount module developed for UMTS EGSM. This power amplifier module operates in the 880-915MHz bandwidth. The ACPM-7372 meets stringent UMTS linearity requirements up to 28.75dBm output power. The 4mmx4mm form factor package is self contained, incorporating 50ohm input and output matching networks ...
Page 2
Absolute Maximum Ratings No damage assuming only one parameter is set at limit at a time with all other parameters set at or below nominal value. Operation of any single parameter outside these conditions with the remaining parameters set at ...
Page 3
Electrical Characteristics for WCDMA Mode – Conditions: �cc = 3.4�, �en = 2.6� 25°C, �in/�out = 50ohm – Signal Configuration: 3GPP (DPCCH + 1DPDCH) Up-�ink unless specified otherwise. 3GPP (DPCCH + 1DPDCH) Up-�ink unless specified otherwise. (DPCCH + ...
Page 4
Electrical Characteristics for WCDMA Mode – Conditions: �cc = 3.4�, �en = 2.6� 25°C, �in/�out = 50ohm – Signal Configuration: 3GPP (DPCCH + 1DPDCH) Up-�ink unless specified otherwise. 3GPP (DPCCH + 1DPDCH) Up-�ink unless specified otherwise. (DPCCH + ...
Page 5
... All dimensions are in millimeter 1.90 1.70 0.85 1.20 X-Ray Top View Package Dimensions All dimensions are in millimeter Pin 1 Mark ± 0.1 Marking Specification Pin 1 Mark AVAGO ACPM-7372 PYYWW AAAAA 5 PIN Description Pin # 1 0.40 2 0. 1.90 0.6 4 ± 0.1 0.9 ± 0.1 ...
Page 6
... CoolPAM Avago Technologies’ CoolPAM is stage-bypass PA tech- nology which saves more power compared with conven- tional PA. With this technology, the ACPM-7372 has very low quiescent current, and efficiencies at low and medium output power ranges are high. Incorporation of bias circuit The ACPM-7372 has internal bias circuit, which removes the need for external constant voltage source (� ...
Page 7
... Bypass cap C1, C2 and C3 should be also placed nearby from pin5, pin4 and pin3, respectively. The length of post-PA transmission line should be minimized to reduce line loss. Peripheral Circuits PA_ON BB PA_R0 C1 PA_R1 C2 C3 ACPM-7372 Ven GND RF In Vmode GND Vbp OUT TX filter IN GND Vc1 ...
Page 8
Metallization 0.1 0.6 0.4 0.85 0.25 0.5 Ø0.3mm on 0.6mm pitch Solder Mask Opening 0.7 0.55 0.5 1.8 0.85 2.4 Solder Paste Stencil Aperture 0.6 0.5 0.4 0.85 2.0 8 PCB Design Guidelines The recommended PCB land pattern is shown ...
Page 9
... Evaluation Board Schematic Ven 1 Ven C1 Vmode 100pF 2 Vmode C2 100pF Vbp 3 Vbp 100pF Vcc1 5 Vcc1 C4 C5 680pF 2.2uF Evaluation Board Description AVAGO ACPM-7372 PYYWW AAAAA GND 10 GND 9 RF out 8 GND 7 Vcc2 6 C6 680pF C7 RF out Vcc2 C7 2.2uF ...
Page 10
Tape and Reel Information Dimension List Annote Millimeter Annote A0 4.40±0. 4.40±0.10 P10 K0 1.70±0. 1.55±0.05 �� D1 1.60±0. 4.00±0. 8.00±0.10 Tape and �eel ��ormat – mm. 10 ...
Page 11
Reel Drawing BACK VIEW 25 min wide (ref) Slot for carrier tape insertion for attachment to reel hub (2 places 180° apart) FRONT VIEW Plastic �eel ��ormat (all dimensions are in millimeters) 11 Shading indicates thru slots +0.4 178 -0.2 ...
Page 12
... After this time period, the part would need to be removed from the reel, de-taped and then re-baked. MS� classification reflow temperature for the ACPM-7372 is targeted at 260°C +0/-5°C. ��igure and table on next page show typical SMT profile for maximum temperature of 260 +0/-5°C. ...
Page 13
Reflow Profile Recommendations Tsmax Tsmin ts Preheat 25 t 25°C to Peak Typical SMT �eflow Profile for Maximum Temperature = 260 +0/-5°C. Typical SMT Reflow Profile for Maximum Temperature = 260 +0/-5°C Profile Feature Average ramp-up rate ...
Page 14
Storage Condition Packages described in this document must be stored in sealed moisture barrier, antistatic bags. Shelf life in a sealed moisture barrier bag is 12 months at <40°C and 90% relative humidity (�H) J-STD-033 p.7. Out-of-Bag Time Duration After ...
Page 15
Recommended Equivalent Total Floor Life (days) @ 20°C, 25°C & 30°C, 35°C ��or ICs with Novolac, Biphenyl and Multifunctional Epoxies (�eflow at same temperature at which the component was classified) Maximum Percent �elative Humidity Maximum Percent Relative Humidity Package Type ...
Page 16
For product information and a complete list of distributors, please go to our web site: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © ...