Optocoupler

HCNW135

Manufacturer Part NumberHCNW135
DescriptionOptocoupler
ManufacturerAvago Technologies US Inc.
HCNW135 datasheet
 


Specifications of HCNW135

No. Of Channels1Isolation Voltage5kV
Optocoupler Output TypePhototransistorInput Current16mA
Output Voltage20VOpto Case StyleDIP
No. Of Pins8Ctr Max50%
Propagation Delay Low-high2µsCtr Min5%
Voltage - Isolation5000VrmsNumber Of Channels1, Unidirectional
Current - Output / Channel8mAData Rate1Mbps
Propagation Delay High - Low @ If200ns @ 16mACurrent - Dc Forward (if)25mA
Input TypeDCOutput TypeOpen Collector
Mounting TypeThrough HolePackage / Case8-DIP (0.400", 10.16mm)
Lead Free Status / RoHS StatusContains lead / RoHS non-compliantOther names516-1025-5
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
9
Page 9
10
Page 10
11
12
13
14
15
16
17
Page 1/17

Download datasheet (664Kb)Embed
Next
6N135/6, HCNW135/6
HCPL-2502/0500/0501
Single Channel, High Speed Optocouplers
Data Sheet
Lead (Pb) Free
RoHS 6 fully
compliant
RoHS 6 fully compliant options available;
-xxxE denotes a lead-free product
Description
These diode-transistor opto coup lers use an insulating
layer between a LED and an integrated photodetector to
provide elec trical in su lation between input and out put.
Separate connections for the photodiode bias and out-
put-transistor collector increase the speed up to a hun-
dred times that of a conven tional phototransistor coupler
by reduc ing the base-collector capacitance.
These single channel optocoup lers are available in
8-Pin DIP , SO-8 and Widebody package configurations.
The 6N135, HCPL-0500, and HCNW135 are for use in TTL/
CMOS, TTL/LSTTL or wide bandwidth analog applications.
Current transfer ratio (CTR) for these devices is 7% mini-
mum at I
= 16 mA.
F
The 6N136, HCPL-2502,
HCPL-0501, and HCNW136 are
designed for high speed TTL/TTL applications. A standard
16 mA TTL sink current through the input LED will pro-
vide enough output current for 1 TTL load and a 5.6 kΩ
pull-up resistor. CTR for these devices is 19% minimum at
I
= 16 mA.
F
Functional Diagram
8
NC
1
V
CC
7
ANODE
2
V
B
6
CATHODE
3
V
O
NC
4
5
GND
A 0.1 µF bypass capacitor must be connected between pins 5 and 8.
CAUTION: It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and/or degradation which may be induced by ESD.
Features
• High speed: 1 Mb/s
• TTL compatible
• Available in 8-Pin DIP, SO-8, widebody packages
• Open collector output
• Safety approval
UL Recognized – 3750 V
for 1 minute for HCNW and Option 020 devices)
per UL1577
CSA Approved
IEC/EN/DIN EN 60747-5-2 Approved
– V
= 560 V peak for SO8 devices
IORM
– V
= 630 V peak for DIP 300mil devices
IORM
– V
= 1414 V peak for DIP 400mil (widebody)
IORM
devices
• Dual channel version available (253X/053X/0534)
Applications
• High voltage insulation
• Video signal isolation
• Line receivers
• Feedback element in switched mode power supplies
• High speed logic ground isolation
TRUTH TABLE
(POSITIVE LOGIC)
– TTL/TTL, TTL/CMOS, TTL/LSTTL
LED
V
O
• Replaces pulse transformers
ON
LOW
OFF
HIGH
• Replaces slow phototransistor isolators
• Analog signal ground isolation
for 1 minute (5000 V
rms
rms

HCNW135 Summary of contents

  • Page 1

    ... These single channel optocoup lers are available in 8-Pin DIP , SO-8 and Widebody package configurations. The 6N135, HCPL-0500, and HCNW135 are for use in TTL/ CMOS, TTL/LSTTL or wide bandwidth analog applications. Current transfer ratio (CTR) for these devices is 7% mini- mum ...

  • Page 2

    ... Avago publications GND 8-Pin DIP (300 Mil) Single Dual Channel Channel Package Package* 6N135 HCPL-2530 6N136 HCPL-2531 HCPL-2502 Small-Outline Widebody SO-8 Single Dual Channel Channel Package Package* HCPL-0500 HCPL-0530 HCNW135 HCPL-0501 HCPL-0531 HCNW136 (400 Mil) Single Channel Package ...

  • Page 3

    ... Ordering Information 6N135, 6N136, HCPL-2502, HCPL-0500, HCPL-0501 are UL Recognized with 3750 Vrms for 1 minute per UL1577. HCNW135, HCNW136 are UL Recognized with 5000 Vrms for 1 minute per UL1577. All devices above listed are approved under CSA Component Acceptance Notice #5, File CA 88324. Option ...

  • Page 4

    Package Outline Drawings 8-Pin DIP Package (6N135/6, HCPL-2502) 9.65 ± 0.25 (0.380 ± 0.010 TYPE NUMBER A XXXXZ R U YYWW 1.78 (0.070) MAX. 1.19 (0.047) MAX. 3.56 ± 0.13 (0.140 ± ...

  • Page 5

    ... TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH) 5.207 ± 0.254 (0.205 ± 0.010) DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX. 8-Pin Widebody DIP Package (HCNW135/6) 11.23 ± 0.15 (0.442 ± 0.006 HCNWXXXX ...

  • Page 6

    ... Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW135/6) 11.23 ± 0.15 (0.442 ± 0.006 1.55 (0.061) MAX. 1.80 ± 0.15 (0.071 ± 0.006) 2.54 (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. ...

  • Page 7

    Recommended Pb-Free IR Profile * 260 +0/-5 ° 217 ° RAMP-UP 3 °C/SEC. MAX. 150 - 200 °C T smax T smin t s PREHEAT 60 to 180 SEC °C to PEAK TIME ...

  • Page 8

    ... Product Safety Regulations section IEC/EN/DIN EN 60747-5-2, for a detailed description. Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application. IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (HCNW135/6 ONLY) Description Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤ ...

  • Page 9

    Absolute Maximum Ratings Parameter Storage Temperature* Operating Temperature* Average Forward Input Current* Peak Forward Input Current* (50% duty cycle pulse width) (50% duty cycle pulse width) Peak Transient Input Current* (≤1 µs pulse width, 300 pps) ...

  • Page 10

    ... Parameter Symbol Device Current CTR* 6N135 Transfer Ratio HCPL-0500 HCNW135 HCPL-2502 6N136 HCPL-0501 HCNW136 Logic Low V 6N135 OL Output Voltage HCPL-0500 HCNW135 6N136 HCPL-2502 HCPL-0501 HCNW136 Logic High Output Current Logic Low I CCL Supply Current Logic High I * CCH Supply Current Input Forward ...

  • Page 11

    ... HCPL-0501 Common Mode |CM | 6N135 L Transient Im- HCPL-0500 munity at Logic HCNW135 Low Level 6N136 Output HCPL-2502 HCPL-0501 Bandwidth BW 6N135/6 HCPL-2502 HCPL-0500/1 HCNW135/6 *For JEDEC registered parts. **All typicals 25° 0°C to 70°C unless otherwise specified Min. Typ.** Max. Units µs 0.2 1 25° ...

  • Page 12

    Package Characteristics Over recommended temperature (T Parameter Sym. Device Input-Output V 8-Pin DIP ISO Momentary Withstand Widebody Voltage** 8-Pin DIP (Option 020) I 8-Pin DIP I-O Input-Output R 8-Pin DIP I-O Resistance Widebody Input-Output C 8-Pin DIP I-O Capacitance Widebody ...

  • Page 13

    ... V - FORWARD VOLTAGE - VOLTS F Figure 3. Input current vs. forward voltage. 13 WIDEBODY  5 OUTPUT VOLTAGE - V O WIDEBODY 1.5 HCNW135/6 1.0 0.5 NORMALIZED 0 4  100 I - INPUT CURRENT - mA F WIDEBODY 1000  A 100 10 1 0.001 1.2 1.3 1 ...

  • Page 14

    ... Figure 6. Propagation delay time vs. load resistance. 14 WIDEBODY 1.1 1.0 HCNW135/6 0.9 0.8 0.7 NORMALIZED ° A 0.4 -60 -40 - 100 TEMPERATURE - C ° A WIDEBODY 1000 mA 5 HCNW135 (R = 4.1 k Ω) L 800 HCNW136 (R = 1.9 k Ω) L 600 t t PLH PHL 400 200 0 -60 -40 - 100 T - TEMPERATURE - C ° A WIDEBODY 10 6 5 ° ...

  • Page 15

    ... Figure 9. Thermal derating curve, dependence of safety limiting value with case temperature per IEC/EN/DIN EN 60747-5-2. 15 WIDEBODY + -60 -40 - 100 T - TEMPERATURE - C  A WIDEBODY 0. 100   0.40 0.30 0.20 0. QUIESCENT INPUT CURRENT - mA F HCNW135/6 1000 P (mW) S 900 I (mA) S 800 700 600 500 400 300 200 100 100 125 150 175 T - CASE TEMPERATURE - C  S ...

  • Page 16

    ... Figure 10. Frequency response. 16 6N135/6, HCPL-0500/1, HCPL-2502 + 0.1 µF  2 µF 3  100   51 TRIM FOR UNITY GAIN  22 1N4150 HCNW135/6 8  1.2 K  9.1 K  0.1 µF  470 5  100 2N3904 TYPICAL LINEARITY = ± p-p IN TYPICAL SNR = 50dB  ...

  • Page 17

    1 PHL PLH Figure 11. Switching test circuit 90% 90% 10% 10 SWITCH AT ...