MGA-14516-BLKG Avago Technologies US Inc., MGA-14516-BLKG Datasheet
MGA-14516-BLKG
Specifications of MGA-14516-BLKG
Available stocks
Related parts for MGA-14516-BLKG
MGA-14516-BLKG Summary of contents
Page 1
... LNA designed for optimum use between 1.4GHz to 2.7GHz. For optimum performance at lower frequency from 400MHz to 1.5GHz, the MGA-13516 is recommended. Both MGA-13516 & MGA-14516 share the same package and pinout. Pin Configuration and Package Marking 3 4.0 x 4.0 x 0.85 mm ...
Page 2
Absolute Maximum Rating Symbol Parameter Vdd1 Device Supply Voltage Vbias1 Control Voltage Vdd2 Device Voltage, RF output to ground Vbias Control Voltage Idd2 Device Drain Current Input Power (Vdd1 = 5.0V, Idd1=45mA) in,max [3] P Total ...
Page 3
Demo Board Layout Figure 5. Demo Board Layout Vbias=5V C16 [1] [2] C1 [3] [ Figure 6. Demo Board Schematic 3 Notes: x Recommended PCB material is 10 mils Rogers RO4350. x Suggested component values may vary ...
Page 4
Table1. 1.95 GHz Matching Components Demo board (shown in Figure 5) component values used for demo board schematic in Figure 6. These component values are used when measuring Electrical Specifications and plots of Figure 7 to Figure 17. Part Size ...
Page 5
... MGA-14516 Typical Performance T = 25°C, Vdd1=5V, Vdd2=5V, Vbias=5V unless stated otherwise. Measured on demo board in Figure 5 with compo- A nents listed in Table -60 -40 - Temperature (°C) Figure 7. Idd1 vs. Temperature -60 -40 - Temperature (°C) Figure 9. Ibias vs. Temperature 1.4 1.3 1.2 1.1 1 0.9 0.8 0.7 0.6 0.5 ...
Page 6
... MGA-14516 Typical Performance T = 25°C, Vdd1=5V, Vdd2=5V, Vbias=5V unless stated otherwise. Measured on demo board in Figure 5 with compo- A nents listed in Table 1.65 1.75 1.85 1.95 Frequency (GHz) Figure 12. OIP3 vs. Frequency and Temperature Frequency (GHz) Figure 14. IRL & ORL vs. Frequency 1.7 1.9 2.1 2 ...
Page 7
... MGA-14516 Scattering Parameter and Noise Parameter Test Setup Figure 18. Test setup for Q1 S & Noise Parameters data. 7 Figure 19. Test setup for Q2 S & Noise Parameters data. C18=10pF (Kyocera CM05CH100J50AHF) and R4=220Ω (Rohm MCR01MZSJ221). ...
Page 8
... Note: S-parameters are measured on PCB. The PCB material is 10 mils Rogers RO4350. Figure 18 shows the input and output reference planes. MGA-14516 Q1 Typical Noise Parameter, Vdd1=5V, Idd1=45mA Freq (GHz) Fmin(dB) mag 1.5 0.38 0.38 1.7 0.45 ...
Page 9
... MGA-14516 Q2 Typical Scattering Parameters, Vdd2=5V, Vbias=5V, IDD2=110mA S11 Freq (GHz) Mag Ang 0.1 0.19 -147.9 0.5 0.17 149.6 0.9 0.17 122 1 0.17 115.6 1.5 0.12 76.4 1.9 0.09 -9.4 2 0.1 -34.3 2.5 0.25 -95.1 3 0.34 -115 3.5 0.52 -126.2 4 0.63 -154 ...
Page 10
... Part Number Ordering Information Part Number No. of Devices MGA-14516-TR1G 1000 MGA-14516-TR2G 3000 MGA-14516-BLKG 100 SLP4X4 Package Dimension Pin 1 Dot 4.00 ± 0.10 by marking 14516 4.00 ± 0.10 YYWW XXXX Top View Notes: 1. All dimensions are in millimeters. 2. Dimensions are inclusive of plating. 3. Dimensions are exclusive of mold ash and metal burr. ...
Page 11
PCB Land Pattern and Stencil Design 0.650 0.300 0.650 2.200 PCB Land Pattern (Top View) 2.200 1.980 0.650 0.300 0.270 0.485 Combines PCB & Stencil Layouts All Dimension are 0.270 2.200 0.485 0.350 2.200 1.980 0.650 1.980 ...
Page 12
Device Orientation REEL USER FEED COVER TAPE DIRECTION Tape Dimensions 8.0 ±0.10 4.0 ±0.10 12.00 +0.30/-0.10 4.25 ±0. 14516 YYWW CARRIER XXXX TAPE 2.00 ±0.05 .279 ±0.02 10º MAX. 1.13 ±0.10 Ko USER FEED DIRECTION 14516 14516 YYWW ...
Page 13
Reel Dimension - 7 Inch FRONT VIEW TAPE A WIDTH MAX +1.5–0.0 12mm 18.00 C1 TAPE SLOT Note: Surface resistivity to be <10 PLANE VIEW 13 BACK VIEW SPECIFICATION ±0.5 ±0.5 (max) (min) ±0.2 12.4 ...
Page 14
Reel Dimension - 13 Inch ESD Label (See Below) RECYCLE SYMBOL DETAIL “X” EMBOSSED LINE X2 90.0mm length LINES 147.0mm AWAY FROM CENTER POINT EMBOSSED ‘M’ 5.0mm height RECYCLE SYMBOL DETAIL “X” For product information and a complete list of ...