MGA-655T6-BLKG Avago Technologies US Inc., MGA-655T6-BLKG Datasheet - Page 4

• Manufacturer Part Number: MGA-655T6-BLKG
• Description: IC,Microwave/Millimeter Wave Amplifier,SINGLE,GAAS,LLCC,6PIN,PLASTIC
• Manufacturer: Avago Technologies US Inc.
• Type: Low Noiser

Specifications of MGA-655T6-BLKG

• Current - Supply: 10mA
• Frequency: 2.5GHz ~ 4GHz
• Gain: 14.7dB
• Noise Figure: 1.17dB
• P1db: 12dBm
• Package / Case: 6-XFDFN Exposed Pad
• Rf Type: General Purpose
• Test Frequency: 3.5GHz
• Voltage - Supply: 3V
• Amplifier Type: MMIC
• Bandwidth: 2.5 to 4 GHz
• Current, Input Bias: 10 mA
• Impedance, Thermal: 75 °C/W
• Power Dissipation: 66 mW
• Voltage, Supply: 4 V
• Manufacturer's Type: Low Noise Amplifier
• Number Of Channels: 1
• Supply Current: 14@3VmA
• Frequency (max): 4GHz
• Operating Supply Voltage (typ): 3V
• Package Type: Ultra Thin profile
• Mounting: Surface Mount
• Pin Count: 6
• Noise Figure (typ): 1.2@3500MHzdB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Demo Board Layout
Figure 4. Demo board layout diagram*
*Application Notes:
1. Performance in a specified frequency band can be optimized by changing component values in the demoboard above to suit the application at
2. Operational Logic of Bypass pin (Pin 1):
Demo Board Schematic for 3.5 GHz Application
RF
Figure 5. Demo board schematic diagram
4
V
BYPASS
IN
that frequency. The following graphs show components used to demonstrate performance at the (3 - 4) GHz band.
Pin 1 voltage in LNA mode can be varied to enable the LNA bias current to be adjusted.
- Normal LNA operation: [2 to 2.7] volt,
- Bypass mode: [0 to 0.2] volt
L1
C5
1
2
3
BIAS/CONTROL
MGA 655T6
6
5
4
NC
C2
L2
C3
R1
L3
*Jumpers indicated in the demo board drawing are not
needed in actual application board; this is because generic
demo boards were used for development.
Part
J2*,
J1*
C2
C3
C4
C5
R1
J3*
L1
L2
L3
C4
RF
V
DD
OUT
0402
0402
0402
0402
0402
0402
0402
0402
0402
Size
Notes:
1. L1 is an input matching inductor.
2. L2 and C2 form the output matching
3. R1&L3 is a network that isolates the
4. C3 is a RF bypass capacitor.
network.
measurement demoboard from external
disturbances. C4 and C5 migrate the
effect of external noise pickup on the
V
are not required in actual operation.
5.1 ohm MCR Series (Rohm)
1000 pF MCH155 Series (Rohm)
10.0 nH LLP1005 Series (TOKO)
dd
1.2 nH
1.0 nH
0 ohm
4.7 pF
4.7 pF
0.1 uF
Value
and V
bypass
P/N
LLP1005 Series (TOKO)
LLP1005 Series (TOKO)
C1005C0G1H4R7C (TDK)
C1005C0G1H4R7C (TDK)
MCH155 Series (Rohm)
RK73Z1E000 (KOA)
Copper Foil
lines. These components