V250 BOGEN COMMUNICATIONS, V250 Datasheet - Page 2

• Manufacturer Part Number: V250
• Description: Power Vector Modular Input Amplifiers
• Manufacturer: BOGEN COMMUNICATIONS

Specifications of V250

• Peak Reflow Compatible (260 C): No
• Leaded Process Compatible: No
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Specifications
Specifications
Power Output (RMS):
Frequency Response
Distortion
Signal-to-Noise
Tone Controls
Sensitivity
Output Regulation:
Output Impedance
* Typical, @1 kHz/0.1% THD/4W direct
Architect and
Technical
Engineer
†
The amplifier shall be a Bogen Power Vector Amplifier,
Model V35, V60, V100, V150, or V250. The amplifier shall
be compatible with both high- (70/25V) and low- (4/8-
ohm) impedance speakers, with the capability of 35, 60,
100, 150, or 250 watts, respectively.
The amplifier shall provide 8 module bays for plug-in input
modules with two of the bays also capable of handling
plug-in signal-processing output modules. There shall be
4 levels of priority available between all modules.
Each of the 8 module bays shall have an associated inde-
pendent volume control. Each independent volume con-
trol shall have a signal/clip LED to indicate signal condi-
tion. Each amplifier shall also include bass and treble con-
trols, as well as a motorized master volume control, which
can be remotely operated using the RVCP accessory
(sold separately).
For larger applications, the amplifier shall be able to
bridge to another Power Vector amplifier or mixer using a
built-in bridging jack and mute terminals. This connection
shall effectively increase the number of inputs.
An 11-segment LED output level meter will register either
the average or peak level of the amplifierʼs output level, as
selected by an Average/Peak switch. Each Power Vector
amplifier shall have a Tone Control Bypass switch and a
Low-Cut Filter switch, both located on the rear of the
amplifier in module bay 6.
35W
45W
45 Hz to 20 kHz; +0/-2 dB
20 Hz to 20 kHz; +0/-1 dB
< 0.5%**
< 0.1%** (.05 typical @ 1 kHz)
-94 dB
-70 dB
-60 dB
-70 dB
@100 Hz (+/- 10 dB minimum)
@10 kHz (+/- 10 dB minimum)
@125 Hz (-6 dB/octave)
0.4V (at module bay connector)
2 dB or better, no load to full load
70V, 25V, 8 ohms (bal or unbal)
4 ohms (minimum)
V35
60W
85W
V60
** THD+N, Maximum, Full bandwidth @ FRP
100W
140W
V100
150W 250W
200W 340W
V150
V250
Inserts
Bridging In/Out
Pre-EQ Output
AC Power Receptacle:
AC Voltage:
AC Current:
Product Weight (lb.):
Dimensions:
† Referenced to FRP output level, 20-20 kHz bandwidth limited
A lockable switch will permit the selection of transformer-
coupled output or direct output for speaker connections.
Signal-processing Insert jacks (RCA connectors) will
allow external equipment to be inserted between the pre-
amp output and the power amp input.
Each model will have a Pre-EQ, unbalanced (RCA jack),
buffered output whose signal is post all volume controls,
tone controls, and output module signal-processing, but
before (pre-EQ) any external signal-processing equip-
ment connected to the Insert jacks.
Each amplifier will have bridging in/out capability and indi-
vidual access to internal module priority buses for easy
connection of multiple amplifiers or mixers in a system.
Each amplifier will include a 500W maximum, unswitched
AC power receptacle.
The amplifier shall fit into a 19" rack and fit in two rack
spaces (2 RU). It shall allow the attachment of feet for
tabletop placement. Each model shall measure 17-1/4" W
x 3-7/8" H x 14-3/4" D. The V35 shall weigh 22 lb., the
V60 - 26 lb., the V100 - 28 lb., the V150 - 31 lb., and the
V250 - 32 lb.
50 Spring Street, Ramsey, New Jersey 07446, U.S.A.
1VRMS (@FRP)
50 ohms maximum
1VRMS
10k ohms minimum
250 mVRMS (@FRP)
10k ohms maximum
4VRMS (@FRP)
50 ohms maximum
500 watts maximum power,
unswitched
120V AC, 60 Hz
17-1/4" W x 3-7/8" H x 14-3/4" D
(all models)
0.6A
V35
V35
22
1.3A
V60
V60
Tel. [phone] • Fax: [phone]
26
V100 V150 V250
V100 V150 V250
2.0A
28
3.5A
31
www.bogen.com
5.5A
32