AD9269-20EBZ Analog Devices Inc, AD9269-20EBZ Datasheet - Page 30

• Manufacturer Part Number: AD9269-20EBZ
• Description: A/D Converter Eval. Board
• Manufacturer: Analog Devices Inc

Specifications of AD9269-20EBZ

• Silicon Manufacturer: Analog Devices
• Application Sub Type: ADC
• Kit Application Type: Data Converter
• Silicon Core Number: AD9269
• Kit Contents: Software, Evaluation Board
• Number Of Adc's: 2
• Number Of Bits: 16
• Sampling Rate (per Second): 20M
• Data Interface: Serial, SPI™
• Inputs Per Adc: 1 Differential
• Input Range: 2 Vpp
• Power (typ) @ Conditions: 96.9mW @ 20MSPS
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 85°C
• Utilized Ic / Part: AD9269
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

AD9269
The SPI port should not be active during periods when the full
dynamic performance of the converter is required. Because the
SCLK signal, the CSB signal, and the SDIO signal are typically
asynchronous to the ADC clock, noise from these signals can
degrade converter performance. If the on-board SPI bus is used for
other devices, it may be necessary to provide buffers between this
bus and the AD9269 to prevent these signals from transitioning
at the converter inputs during critical sampling periods.
SDIO/DCS and SCLK/DFS serve a dual function when the
SPI interface is not being used. When the pins are strapped to
DRVDD or ground during device power-on, they are associated
with a specific function. The Digital Outputs section describes
the strappable functions supported on the AD9269.
CONFIGURATION WITHOUT THE SPI
In applications that do not interface to the SPI control registers,
the SDIO/DCS pin, the SCLK/DFS pin, the OEB pin, and the
PDWN pin serve as standalone CMOS-compatible control pins.
When the device is powered up, it is assumed that the user intends
to use the pins as static control lines for the duty cycle stabilizer,
output data format, output enable, and power-down feature con-
trol. In this mode, connect the CSB chip select to DRVDD,
which disables the serial port interface.
Table 15. Mode Selection
Pin
SDIO/DCS
SCLK/DFS
OEB
PDWN
External
Voltage
DRVDD (default)
AGND
DRVDD
AGND (default)
DRVDD
AGND (default)
DRVDD
AGND (default)
Configuration
Duty cycle stabilizer enabled
Duty cycle stabilizer disabled
Twos complement enabled
Offset binary enabled
Outputs in high impedance
Outputs enabled
Chip in power-down or standby
Normal operation
Rev. 0 | Page 30 of 40
SPI ACCESSIBLE FEATURES
Table 16 provides a brief description of the general features that
are accessible via the SPI. These features are described in detail
in the AN-877 Application Note, Interfacing to High Speed ADCs
via SPI. The AD9269 part-specific features are described in
detail in Table 17.
Table 16. Features Accessible Using the SPI
Feature
Mode
Clock
Offset
Test I/O
Output Mode
Output Phase
Output Delay
VREF
Allows the user to vary the DCO delay
Description
Allows the user to set either power-down mode
or standby mode
Allows the user to access the DCS via the SPI
Allows the user to digitally adjust the
converter offset
Allows the user to set test modes to have known
data on output bits
Allows the user to set up outputs
Allows the user to set the output clock polarity
Allows the user to set the reference voltage