AD9269-65EBZ Analog Devices Inc, AD9269-65EBZ Datasheet - Page 24

• Manufacturer Part Number: AD9269-65EBZ
• Description: A/D Converter Eval. Board
• Manufacturer: Analog Devices Inc

Specifications of AD9269-65EBZ

• Silicon Manufacturer: Analog Devices
• Application Sub Type: ADC
• Kit Application Type: Data Converter
• Silicon Core Number: AD9269
• Kit Contents: Software, Evaluation Board
• Number Of Adc's: 2
• Number Of Bits: 16
• Sampling Rate (per Second): 65M
• Data Interface: Serial, SPI™
• Inputs Per Adc: 1 Differential
• Input Range: 2 Vpp
• Power (typ) @ Conditions: 191.2mW @ 65MSPS
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 85°C
• Utilized Ic / Part: AD9269
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

AD9269
Jitter Considerations
High speed, high resolution ADCs are sensitive to the quality
of the clock input. The degradation in SNR from the low fre-
quency SNR (SNR
jitter (t
In the previous equation, the rms aperture jitter represents the
clock input jitter specification. IF undersampling applications
are particularly sensitive to jitter, as illustrated in Figure 55.
The clock input should be treated as an analog signal in cases in
which aperture jitter may affect the dynamic range of the AD9269.
To avoid modulating the clock signal with digital noise, keep power
supplies for clock drivers separate from the ADC output driver
supplies. Low jitter, crystal-controlled oscillators make the best
clock sources. If the clock is generated from another type of source
(by gating, dividing, or another method), it should be retimed by
the original clock at the last step.
For more information, see the AN-501 Application Note and the
AN-756 Application Note, available on www.analog.com.
SNR
JRMS
80
75
70
65
60
55
50
45
1
HF
) can be calculated by
= −10 log[(2π × f
Figure 55. SNR vs. Input Frequency and Jitter
LF
) at a given input frequency (f
10
FREQUENCY (MHz)
INPUT
× t
JRMS
)
100
2
+ 10
3.0ps
(
−
SNR
0.05ps
0.2ps
0.5ps
1.0ps
1.5ps
2.0ps
2.5ps
INPUT
LF
/
10
) due to
)
]
1k
Rev. 0 | Page 24 of 40
POWER DISSIPATION AND STANDBY MODE
As shown in Figure 56, the analog core power dissipated by the
AD9269 is proportional to its sample rate. The digital power dis-
sipation of the CMOS outputs is determined primarily by the
strength of the digital drivers and the load on each output bit.
The maximum DRVDD current (IDRVDD) can be calculated as
where N is the number of output bits (34, in the case of the
AD9269).
This maximum current occurs when every output bit switches
on every clock cycle, that is, a full-scale square wave at the Nyquist
frequency of f
lished by the average number of output bits switching, which
is determined by the sample rate and the characteristics of the
analog input signal.
Reducing the capacitive load presented to the output drivers can
minimize digital power consumption. The data in Figure 56 was
taken using the same operating conditions as those used for the
Typical Performance Characteristics, with a 5 pF load on each
output driver.
IDRVDD = V
210
190
170
150
130
110
90
70
10
Figure 56. Analog Core Power vs. Clock Rate
CLK
AD9269-20
20
/2. In practice, the DRVDD current is estab-
DRVDD
30
× C
CLOCK RATE (MSPS)
AD9269-40
LOAD
40
× f
CLK
50
AD9269-65
× N
AD9269-80
60
70
80