5XX MOTHERBOARD ONLY AXIOM, 5XX MOTHERBOARD ONLY Datasheet
5XX MOTHERBOARD ONLY
Specifications of 5XX MOTHERBOARD ONLY
Related parts for 5XX MOTHERBOARD ONLY
5XX MOTHERBOARD ONLY Summary of contents
Page 1
... Development Board for the Motorola MPC5xx Series Microcontrollers © Axiom Manufacturing, 2000 2813 Industrial Lane Garland, TX 75041 (972) 926-9303 FAX (972) 926-6063 email: support@axman.com web: http://www.axman.com Users Manual CMD-5xx Versions CMD-555, CMD560 - 566 ...
Page 2
FEATURES ...................................................................................................................................................................3 CAUTIONARY NOTES ..................................................................................................................................................5 GETTING STARTED ..................................................................................................................................................... ......................................................................................................................................................... 6 OFTWARE EVELOPMENT T S .................................................................................................................................................................. 7 ERMINAL ETTINGS T .................................................................................................................................................................................. 7 UTORIAL Using the Debug Monitor..................................................................................................................................................... 7 Programming the Onboard Flash Memory ........................................................................................................................... 8 MEMORY BANKS AND DEFAULT ...
Page 3
... The CMD-5xx along with a PM-5xx Personality Module is a modular development system for the Motorola series of MPC5xx PowerPC microcontrollers. The system is Plug and Play with the supplied with the Axiom Monitor in the on-board EPROM, 2MByte (512K x 32) Synchronous SRAM, 4MByte (1M x 32) Burstable Flash EPROM, Communication Interfaces, Port Replacement Unit, Keypad and LCD Module support, Serial Cable, Wall Plug power source, printed hardware manual and the UTL5xx CD with programming utilities, support software and technical manuals ...
Page 4
... User Indicators – 4 user indicators to provide user conceived visual response during testing. Axiom development systems provide for low cost software testing with the use of the Monitor in the on-board EPROM. Operation allows the user to load code in the On-Board RAM, Execute application, and display or modify registers or memory. After code is operational the user may relocate the code and reprogram the MPC5xx Internal Flash EEPROM or the boards fixed flash for dedicated operation of new software ...
Page 5
... Axiom Manufacturing reserves the right to make changes without further notice to any products to improve reliability, function or design. Axiom does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under patent rights or the rights of others ...
Page 6
... Your board is now ready to use! If you do not see the monitor prompt, press then release the RESET button on the board. If still no go the text is garbage, see the TROUBLESHOOTING section of this manual. The MEM bank should contain the “Axiom MON5xx” EPROM’s and this bank only should be assigned CS0 to boot the utilities. ...
Page 7
Terminal Settings The utility software provided uses the serial port connected to your PC running a terminal program as described under "Getting Started". While you can use almost any commercial or free serial communications terminal interface important that ...
Page 8
Programming the Onboard Flash Memory After testing your program running out of RAM you will probably want to program it into EEPROM so that it starts whenever power is applied to the board this you must first change ...
Page 9
... Reset start-up) the memory banks can be located at any location in the MPC5xx memory space reference example, Axiom has defined a default memory map where the chip selects are located at predefined locations. The provided software uses this memory configuration. If you modify this memory map make sure that all memory bank and chip select configuration settings are correct ...
Page 10
Synchronous SRAM Memory The synchronous SRAM Memory Bank is composed of four 256K x 32 memory devices. These memory devices are connected in linear order from that the low order address of the memory bank will ...
Page 11
Option Switches and Jumpers Mode Switch 1-4 External Reset Configuration Options and configure the external Hard Reset Configuration Word when enabled. These switches provide a logic 0 Mode Switches low level when off and a ...
Page 12
Memory Device / Bank Selection and Configuration. The CMD-5xx board has three external memory banks and a PRU that provide: 512K x 32bit (2MByte) Synchronous Static RAM (U2 – U5 32bit (4MByte) Burstable Flash EEPROM (U13 - U14) ...
Page 13
... The MEM_EN option jumper is located next to the MAP_SW. When installed it connects chip select CS0* to the MEM sockets U15/U16. The MEM sockets normally contain the Axiom Monitor / Utility firmware EPROM’s that provide board operation from Reset. If the MEM_EN option jumper is removed the MEM sockets memory bank U15/U16 will be disabled and idle. ...
Page 14
Communication Ports The CMD-5xx board provides interfaces for SCI serial ports, 3 TouCan ports and a DLC/J1850 port. COM-1 and COM-2 serial ports with female DB9 connectors are available for RS232 operation of host MPC5xx SCI A ...
Page 15
Data Link Controller / J1850 The CMD-5xx board provides a location to place a J1850 transceiver (Philips AU5780 or Harris HIP7010) for development of a J1850 interface with the MPC565 Data Link Controller integrated peripheral. The board provides a DLC_IN ...
Page 16
... The KEYPAD and KEY_PORT connectors can be used to connect passive keypad devices to the board. Example source code for the LCD and Keypad drivers are provided on the Axiom CMD-5xx support CD. The memory map offset for the LCD / Keypad are determined by the PRU is as follows: ...
Page 17
Personality Module (PM-5xx) Options and Settings The PM-5xx modules provide the CPU with associated support hardware such as oscillator(s), debug support connectors, and options for reconfiguring the CPU. Nexus 50 pin standard development connector is also provided on the MPC561-566 ...
Page 18
PM-561/2/3/4 Hardware Options JP1 Option Jumpers BDM Port operating voltage selection. All 4 jumpers must be optioned the same for correct interface levels on associated signals. The selection of 2.6V or 3.3V operation is dependent on the ...
Page 19
PM-565/6 Hardware Options JP1 Option Jumpers BDM Port operating voltage selection. All 4 jumpers must be optioned the same for correct interface levels on associated signals. The selection of 2.6V or 3.3V operation is dependent on the ...
Page 20
... TROUBLESHOOTING The MEM bank should contain the “Axiom MON5xx” EPROM’s and this bank only should be assigned CS0 to boot trying to boot from external EPROM devices (U15 and U16) be sure the following are all true: a. MODE_SW1 switch 5 must be ON, MODE SW3 position 5 OFF. ...