M24308/2-2F Cinch Connectors, M24308/2-2F Datasheet - Page 280

• Manufacturer Part Number: M24308/2-2F
• Description: D SUB CONNECTOR, STANDARD, 15POS, RCPT
• Manufacturer: Cinch Connectors
• Type: Cable Socketr

Specifications of M24308/2-2F

• No. Of Contacts: 15
• D Sub Shell Size: DA
• Connector Body Material: Metal
• Gender: Receptacle
• Contact Termination: Crimp
• No. Of Mating Cycles: 500
• Body Material: Steel
• Connector Type: D Sub
• Angle: Straight
• Application: True MIL
• Brand/series: M24308
• Contact Plating: Gold over Nickel
• Current, Rating: 5 A
• Finish, Housing: Zinc Chromate
• Material, Contact: Phosphor Bronze
• Material, Dielectric: Diallyl Phthalate
• Material, Housing: Steel
• Number Of Contacts: 15
• Number Of Rows: 2
• Primary Type: D-Subminiature
• Shell Size: A
• Standards: MIL-C-24308
• Termination: Crimp

6
A full range of tooling is available to make the use of Cinch Miniature Ribbon and
SUPERIBBON™ products as cost-effective as possible. From hand repair tools to
the high production rate Auto-Clinch
your needs.
Auto-Clinch Model 200S Termination Tool
Auto-Clinch is a semi-automatic Connector Termination Machine that terminates
IDC connectors pair-by-pair. The basic machine comes equipped ready to terminate
50-position end-entry Miniature Ribbon or SUPERIBBON connectors, which it can do
in approximately 1.5 minutes.
The Auto-Clinch is pneumatically powered and requires a min. 60psi air supply. It is electrically controlled, and requires a 117V,
60Hz Single Phase electrical circuit (5 Amps). Weight: 120 lbs. (54.48kg.), Dimensions: 25.5" (64.77cm.) wide; 20" (50.8cm) deep; 9"
(22.86cm) high. Note: These specifications may change with the addition of certain options.
Order Part No. AC-371
Several options are available that make the Auto-Clinch a versatile application tool:
AutoClinch is a trademark of Cinch Connector Division of Labinal Components & Systems, Inc.
.085 in. (2.16mm)
Density
Miniature Ribbon
•
•
•
•
•
•
Remote Visual Color Display shows wire color codes. It can be used to train new operators or to assist the operator in
terminating non-standard wire sequences. Part No. ACO-482
The Selective Programmer allows the operator to set the machine to skip over positions that are not to be terminated, thus
speeding up the termination process. Part No. ACO-495
The End-Entry Cable Clamp closer automatically closes the cable clamp on end-entry SUPERIBBON or SuperShield
connectors as they are terminated. Part No. ACO-374
A power assist for this device is also available. Part No. ACO-405
The Top-Entry Adapter dresses the wires during termination such that they are properly aligned for exit through a Top-Entry
hood. Part No. ACO-218
NOTE: Auto-Clinch
Insertion Blades are included for terminating solid wire. For replacement, order Part No. ACB-443
To terminate stranded wire, order stranded-wire blades, Part No. ACB-872
Nests for Panel Mount and Top-Entry Ribbon Connectors, and All Plastic SUPERIBBON connectors allow the use of
Auto-Clinch to terminate other IDC Ribbon Connectors:
Call Toll Free: 1 [phone]
Connector
Size
14
24
36
50
64
* For Bail-Latch plugs with hood where hood forms rear of connector body, i.e., 77-32500.
For overmold kits, use panel mount/top-entry plug nests.
For All-Plastic IDC Connectors
End-Entry
ACEN-850
ACEN-851
ACEN-852
ACEN-853
ACEN-570
TM
cannot be equipped with both Cable Clamp Closer and Top-Entry Adapter simultaneously.
TM
termination tool, Cinch has the tool to fit
Top-Entry
ACTN-568
ACTN-569
ACTN-797
ACTN-798
ACTN-799
Application Tools
6-54
ACMN-484
End-Entry
-
-
-
-
For Metal-Shell IDC Connectors
ACMN-231
ACMN-229
ACMN-228
ACMN-527
Sockets
Panel Mount/Top-Entry
-
ACMN-203
ACMN-858
Plugs
-
-
-
Top-Entry Plug
With Hood*
ACMN-232
ACMN-230
ACMN-227
ACMN-526
-