SIM2060-6-0-18-00-A GLOBAL CONNECTOR TECHNOLOGY, SIM2060-6-0-18-00-A Datasheet - Page 2

• Manufacturer Part Number: SIM2060-6-0-18-00-A
• Description: MEMORY SOCKET, SIM CARD, 6POS
• Manufacturer: GLOBAL CONNECTOR TECHNOLOGY

Specifications of SIM2060-6-0-18-00-A

• Connector Type: SIM Socket
• No. Of Contacts: 6
• Pitch Spacing: 2.54mm
• Contact Material: Copper Alloy
• Contact Plating: Gold
• Contact Termination: Surface Mount Horizontal
• Row Pitch: 7.6mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

A
B
C
D
E
F
G
H
DETAIL
Global Connector Technology Ltd. - SIM2060 : SIM Card Connector, Receiver Type, 6 Pin, SMT, Profile Options: 1.8/2.0/2.2mm
DATE
REV
By
DRAWING
RELEASE
20/06/07
PKN
A
1
1
ECN070913A
13/09/07
PKN
B
ECN080519A
19/05/08
PKN
C
SPECIFICATION
11/06/09
MODIFIED
ASE
D
2
2
3
3
4
4
Third Angle Projection
Dimensions in mm
(Except as noted)
Tolerances
5
5
硬纸板
气泡墊
Part Number:-
Description:-
C
SIM CARD CONNECTOR, RECEIVER TYPE, 6 PIN,
SMT, PROFILE OPTIONS: 1.8/2.0/2.2MM
卷筒
THIS DRAWING IS CONFIDENTIAL AND MUST NOT BE
COPIED OR DISCLOSED WITHOUT WRITTEN CONSENT
SIM2060
1.The 1st & Last 200-300mm at the leading & tail of the CARRY TAPE will not be used.CARRY TAPE
Notes 注意 :
前部分与尾部分各留出 200-300mm 长度不装产品
2.Each cavity will hold 1pc. Placement methods are shown in the diagrams. 每穴放置 1pc 产品，放置
方式如图所示
3.After the packing machine filled the REEL,tangle the REEL one more loop with protection tape,
stick adhesive tape on the four quardrants of the REEL, to aviod out-spreading. Stick 1pc. of label on
each REEL.
包装机包好后 , 再缠上一圈电周波 , 在 REEL 的四个极点贴上胶带 , 以防止 REEL 张开 , 每 REEL 贴 1PC 标签
4. Method of Packing is Hot-Melting. 包装方式是热熔式
5. Firstly put a water-proof bag at the bottom of the carton box, then place 1pc. of hard cardboard on
top, following with 1pc. of bubble-pad, and at the four corners, place the triangular pads, then place
those filled REEL into the center of the carton box. Between the REEL, place 1pc. of bubble-pad as
the separator, until 5pc. of REEL are filled in the box. Then place 1pc of bubble-pad & 1pc. of hard
cardboard on top, close the carton by plastic tape lastly. 先在纸箱底部套上一防水袋 , 再墊上 1pc 硬纸
板后再墊上 1pc 气泡墊 , 四角墊上三角墊 , 度然后把装好产品的 REEL 放进纸箱中 , 每 REEL 之间隔 1pc 气泡
墊 , 依次把 5 REEL 产品放到纸箱中 , 上面再墊上各 1pc 气泡墊及硬纸板 , 最后用胶带封箱 .
6. The peel-off force between the COVER TAPE & CARRY TAPE is: 0.1N-0.7N (variation within
0.3N). Peel-off angle:165-175 degree; Speed of peel-off: 250mm-300mm/min. COVER
TAPE 与 CARRY TAPE 剥离力 :0.1N-0.7N ( 跳动量在 0.3N 以内 ) 剥离角度 :165-175 度 ; 剥离速度 :
250mm-300mm/ 分钟
6
6
Date:-
20 JUN 07
7
Scale
7
NTS
Revision
www.globalconnectortechnology.com
D
GC
Material
See Note
三角墊
防水袋
标签
纸箱
Drawn by
PKN
8
8
E & OE
Sheet No.
2/2
G
A
B
C
D
E
F
H