SIM4055-6-1-22-01-A GLOBAL CONNECTOR TECHNOLOGY, SIM4055-6-1-22-01-A Datasheet - Page 2

• Manufacturer Part Number: SIM4055-6-1-22-01-A
• Description: MEMORY SOCKET, SIM CARD, 6POS
• Manufacturer: GLOBAL CONNECTOR TECHNOLOGY

Specifications of SIM4055-6-1-22-01-A

• Connector Type: SIM Socket
• No. Of Contacts: 6
• Pitch Spacing: 2.54mm
• Contact Material: Copper Alloy
• Contact Plating: Gold
• Contact Termination: Surface Mount Horizontal
• Row Pitch: 7.6mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

A
B
C
D
E
G
H
F
DETAIL
Global Connector Technology Ltd. - SIM4055 : SIM Card Connector, Push Push Type, 6 Pin, SMT, With Card Detect, 2.2mm Profile, With Locating Post
DATE
REV
By
DRAWING
RELEASE
09/04/08
PKN
A
1
1
CORRECTION TO
PIN OUT ERROR
04/11/08
PN
B
PCB LAYOUT & TERMINAL
DETAIL UPDATED
09/09/09
AE
C
2
2
PCB LAYOUT
AMENDED
23/04/10
SA
D
SOLDERING AREA
PLATING UPDATE
14/05/10
SA
E
3
3
PACKING LAYOUT
UPDATE
02/09/10
SA
F
SIM4055-001
12/01/11
ECN:
SA
G
4
4
Third Angle Projection
Dimensions in mm
Tolerances
(Except as noted)
5
5
硬纸板
卷筒
Part Number:-
Description:-
SIM CARD CONNECTOR, PUSH PUSH TYPE, 6 PIN, SMT,
WITH CARD DETECT, 2.2MM PROFILE, WITH LOCATING POST
电周波
气泡垫
C
THIS DRAWING IS CONFIDENTIAL AND MUST NOT BE
COPIED OR DISCLOSED WITHOUT WRITTEN CONSENT
1.The 1st & Last 200-300mm at the leading & tail of the CARRY TAPE will not be used.CARRY TAPE 前
图所示
Notes 注意 :
部分与尾部分各留出 200-300mm 长度不装产品
2.Each cavity will hold 1pc. Placement methods are shown in the diagrams. 每穴放置 1pc 产品,放置方式如
3.After the packing machine filled the REEL,tangle the REEL one more loop with protection tape, stick
adhesive tape on the four quardrants of the REEL, to aviod out-spreading. Stick 1pc. of label on each
REEL. 包装机包好后,再缠上一圈电周波,在 REEL 的四个极点贴上胶带,以防止 REEL 张开 , 每 REEL 贴 1PC
标签
4. Use sticking cover tape to seal carrier tape. 使用自粘式载带
5. Firstly put a water-proof bag at the bottom of the carton box, then place 1pc. of hard cardboard on top,
following with 1pc. of bubble-pad, and at the four corners, place the triangular pads, then place those
filled REEL into the center of the carton box. Between the REEL, place 1pc. of bubble-pad as the
separator, until 5pc. of REEL are filled in the box. Then place 1pc of bubble-pad & 1pc. of hard cardboard
on top, close the carton by plastic tape lastly. 先在纸箱底部套上一防水袋 ,再墊上 1pc 硬纸板后再墊上 1pc
气泡墊,四角墊上三角墊,度然后把装好产品的 REEL 放进纸箱中,每 REEL 之间隔 1pc 气泡墊,依次把 5
REEL 产品放到纸箱中,上面再墊上各 1pc 气泡墊及硬纸板,最后用胶带封箱
6. The peel-off force between the COVER TAPE & CARRY TAPE is: 0.1N-0.7N (variation within 0.3N).
Peel-off angle:165-175 degree; Speed of peel-off: 250mm-300mm/min. COVER TAPE 与 CARRY TAPE 剥
离力 :0.1N-0.7N ( 跳动量在 0.3N 以内 ) 剥离角度 :165-175 度 ; 剥离速度 : 250mm-300mm/ 分钟
SIM4055
6
6
Date:-
09 APR 08
7
7
Scale
NTS
Revision
www.globalconnectortechnology.com
G
GC
See Note
Material
三角垫
标签
纸箱
Drawn by
PKN
8
8
E & OE
Sheet No.
2/2
A
B
C
D
E
G
H
F