83-1SP (PL-259) AMPHENOL RF, 83-1SP (PL-259) Datasheet - Page 3

• Manufacturer Part Number: 83-1SP (PL-259)
• Description: RF/COAXIAL, UHF PLUG, STRAIGHT, SOLDER
• Manufacturer: AMPHENOL RF
• Type: Cable Plugr

Specifications of 83-1SP (PL-259)

• Body Style: Straight Plug
• Coaxial Termination: Solder
• Rg Cable Type: RG-8, 9, 87A, 213, 214, 225
• Contact Material: Brass
• Contact Plating: Silver
• Frequency Max: 300MHz
• Connector Type: UHF Coaxial
• Angle: Straight
• Application: True MIL
• Cable Type: RG/U 8,9,11,13,63,87A,149,213,214,216,225
• Finish, Housing: Silver
• Gender: Female
• Material, Contact: Beryllium Copper
• Material, Dielectric: TFE
• Material, Housing: Brass
• Mating Type: Threaded
• Primary Type: UHF
• Temperature, Operating, Maximum: 165 °C
• Termination: Solder
• Voltage, Rating: 500 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Assembly Instructions-C4, C5
UHF
C4 — BRAID CRIMP - SOLDER CENTER CONTACT
C5 — UHF CRIMP-CRIMP TYPE-C5
Amphenol Corporation Tel: [phone]
Amphenol
Amphenol
Number
83-58DCP-2
83-58DCP-2RFX
Step 1
Step 2
Step 3
83-58SP
83-58SP-1002
83-59DCP-RFX
83-58SCP-RFX
83-59SP
83-8SP-RFX
Number
Step 1
Step 2
Step 3
(3) crimp
Connector Cable
Connector
UHF Plug
UHF Plug
UHF Plug
UHF Plug
UHF Plug
UHF Plug
UHF Plug
UHF Plug
Type
Type
(2) crimp
RG-/U
58
58
RG-/U
58, 141
Cable
400
59
58
59
a
braid after flaring
8
Cable Attachment
Outer
Crimp
Crimp
(1) crimp
b
c
a
body assembly
Cable Attachment
Inner
Crimp
Crimp
b
Outer
Crimp
Crimp
Crimp
Crimp
Crimp
Crimp
outer ferrule
ferrule
c
braid after flaring
Outer ferrule End of Ferrule Center Contact
Cavity for
Solder
Solder
Solder
Solder
Solder
Solder
Inner
.260(6.60)
body assembly
.255(6.5)
coupling nut
coupling nut
Outer Ferrule
.429(10.9)
Cavity for
276
.213(5.4)
.213(5.4)
.255(6.5)
.213(5.4)
.255(6.5)
Cavity for
Hex Crimp Data
.210(5.33)
.213(5.4)
Step 1 Strip cable to dimensions shown. Slide ferrule and coupling
Step 2 Slide body assembly into place so inner ferrule portion slides
Step 3 Using tools indicated in table above:
Step 1 Cut end of cable even. Strip cable to dimensions shown in
Step 2 Slide coupling nut and ferrule over cable jacket. Flair braid
Step 3 Soft solder center conductor to contact. Avoid heating
body assembly
body assembly
Hex Crimp Data
nut over cable jacket and flair braid slightly as shown.
under braid. Braid must butt back of body. Slide coupling
nut forward. Slide ferrule over braid until it butts against
body.
(1) crimp center contact
(2) crimp outer ferrule to braid
(3) crimp outer ferrule to cable jacket
Tool 227-994
227-1221-11
227-1221-11
227-1221-13
227-1221-11
227-1221-13
227-1221-25
table. All cuts are to be sharp and square. Do not nick
braid, dielectric or center conductor. Tin center conductor
avoiding excessive heat.
slightly as shown. Install cable into body assembly, so
inner ferrule portion slides under braid, until braid butts
shoulder. Slide outer ferrule over braid until it butts shoulder.
Crimp ferrule with tool and die set indicated in table.
contact excessively to prevent damaging insulator.
Slide/screw coupling nut over body.
.052(1.32) sq.
Cavity for
Die Set
.068(1.7)
CTL Series
1.23(31.3) .791(20.2) .25(6.35)
1.12(28.4) .685(17.4) .236(5.99)
Tool No.
CTL-1
CTL-1
CTL-1
CTL-1
CTL-1
CTL-3
a
1.14(29.0)
1.14(29.0)
1.22(30.9)
1.22(30.9)
1.22(30.9)
1.22(30.9)
b
Stripping Dims, inches (mm)
a
Amphenol
c
.780(19.9)
.780(19.9)
.574(22.6)
.574(22.6)
.574(22.6)
.574(22.6)
Series
www.amphenolrf.com
Tool #
b
CTL-1
CTL
—
.543(13.8)
.543(13.8)
.543(13.8)
.543(13.8)
227-1221-11,-13
.250(6.4)
.250(6.4)
Die Set
for Tool
227-944
227-1350
c
®