MCWL05JT6N8 MULTICOMP, MCWL05JT6N8 Datasheet - Page 9

• Manufacturer Part Number: MCWL05JT6N8
• Description: INDUCTOR, 6.8NH, 600MA, 5%, 5.5GHz
• Manufacturer: MULTICOMP

Specifications of MCWL05JT6N8

• Inductance Tolerance: ± 5%
• Dc Resistance Max: 110mohm
• Dc Current Rating: 600mA
• Self Resonant Frequency: 5.5GHz
• Core Material: Ceramic
• Inductor Case Style: 0805
• No. Of Pins: 2
• Inductance: 6.8nH
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

■Environmental Characteristics
Electrical Performance Test
Mechanical Performance Test
Climatic Test
Tel: [phone]
Inductance
Q
SRF
DC Resistance RDC
Rated Current IDC
Over Load
Withstanding Voltage
Insulation Resistance
Vibration
Resistance to Soldering Heat
Component Adhesion
(Push Test)
Drop
Solderability
Resistance to Solvent
Temperature Characteristic
Humidity
Low Temperature Storage
Thermal Shock
High Temperature Storage
High Temperature Load Life
Damp Heat with Load
Storage Temperature: 25±3°C; Humidity < 80%RH
Item
Item
Item
Fax: [phone]
Appearance: No damage
L change: within ±5%
Q change: within ±10%
1 lbs. For 0402
2 lbs. For 0603
3 lbs. For the rest
No damage
90% covered with solder
No damage on appearance and
marking
Appearance: No damage
L change: within ±10%
Q change: within ±20%
There should be no evidence of short
of open circuit.
Refer to standard electrical
characteristic spec.
Inductors shall have no evidence of
electrical and mechanical damage
Inductors shall be no evidence of
electrical and mechanical damage.
1000M ohm min.
Requirement
Requirement
Requirement
E-mail:
[e-mail]
HP4286
HP4286
HP4287
Micro-Ohm meter (Gom-801G)
Applied the current to coils, The inductance change should be less
than 10% to initial value
Applied 2 times of rated allowed DC current to inductor for a period
of 5 minutes
AC voltage of 500 VAC applied between inductors terminal and
case for 1 min.
100 V
Test device shall be soldered on the substrate
Oscillation Frequency: 10 to 55 to 10Hz for 1 min.
Amplitude: 1.5 mm
Time: 2 hrs for each axis (X, Y &Z), total 6 hrs
Solder Temperature: 270±5°C
Immersion Time: 10±2 seconds
The device should be soldered (260±5 for 10 seconds) to a tinned
copper subs rate. A dynamiter force gauge should be applied to
the side of the component. The device must with stand a minimum
force of 2 or 4 pounds without a failure of adhesion on termination
Dropping chip by each side and each corner. Drop 10 times in total
Drop height: 100 cm
Drop weight: 125 g
Inductor shall be dipped in a melted solder bath at 245±5 for 3
seconds
MIL-STD202F, Method 215D
-40~+125°C
Temperature: 40±2°C
Relative Humidity: 90~95%
Time: 96±2 hrs
Measured after exposure in the room condition for 2 hrs
Temperature: -40±2°C
Time: 96±2 hrs
Inductors are tested after 1 hour at room temperature
One cycle:
Total: 5 cycles
Temperature: 125±2°C
Time: 96±2 hrs
Measured after exposure in the room condition for 1hour
Temperature: 85±2°C
Time: 1000±12 hrs
Load: Allowed DC current
Temperature: 40±2°C
Relative Humidity: 90~95%
Time: 1000±12 hrs
Load: Allowed DC current
Step
1
2
3
4
DC
applied between inductor terminal and case
Temperature（°C）
-25±3
25±2
125±3
25±2
http://www.viking.com.tw
Test Method
Test Method
Test Method
Time（min.）
30
15
30
15
39