MCHP06W2F560JT5E MULTICOMP, MCHP06W2F560JT5E Datasheet

RESISTOR, HIGH POWER, 56OHM, 500mW, 1%

MCHP06W2F560JT5E

Manufacturer Part Number
MCHP06W2F560JT5E
Description
RESISTOR, HIGH POWER, 56OHM, 500mW, 1%
Manufacturer
MULTICOMP
Series
HP06r
Datasheet

Specifications of MCHP06W2F560JT5E

Resistance
56ohm
Resistance Tolerance
± 1%
Power Rating
500mW
Voltage Rating
50V
Resistor Element Material
Thick Film
Temperature Coefficient
± 100ppm/°C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Specification Table
Power Rating:
Resistors shall have a power rating based on continuous load operation at an ambient temperature of 70°C. For temperature in
excess of 70°C, the load shall be derate.
Voltage rating:
Resistors shall have a rated direct-current (DC) continuous working voltage or an approximate sine-wave root-mean-square (RMS)
alternating-current (AC) continuous working voltage at commercialline frequency and waveform curresponding to the power rating, as
determined from the following formula :
Where : RCWV = Rated DC or RMS AC continuous working voltage at commercial-line frequency and waveform (volt).
In no case shall the rated DC or RMS AC continuous working voltage be greater than the applicable maximum value.
HP06
Type
HP06 Series High Power Resistors
Power Rating
0.50
(W)
P = Power rating (watt)
R = Nominal resistance (ohm)
Maximum Working
Voltage
Ambient temperature (°C)
(V)
50
RCWV = √P x R
Maximum Overload
Voltage
100
(V)
Page <1>
Withstanding Voltage
Dielectric
300
(V)
Temperature
-55 to +155
Range
(°C)
03/05/08 V1.1
Temperature
Ambient
(°C)
70

Related parts for MCHP06W2F560JT5E

MCHP06W2F560JT5E Summary of contents

Page 1

... HP06 0.50 Power Rating: Resistors shall have a power rating based on continuous load operation at an ambient temperature of 70°C. For temperature in excess of 70°C, the load shall be derate. Voltage rating: Resistors shall have a rated direct-current (DC) continuous working voltage or an approximate sine-wave root-mean-square (RMS) ...

Page 2

... HP06 Series High Power Resistors Construction: 1. High Purity Alumima Substrate. 2. Protective covering. 3. Resistive covering. 4. Termination inner (Ag/Pd). 5. Termination (between) Ni plating. 6. Termination (outer) Sn plating. Power rating and dimensions Dimensions Type L 1.55 + 0.15 HP06 3.10 ±0.15 Power Rating Power Rating Type at 70°C ...

Page 3

... HP06 Series High Power Resistors Performance specification Characteristics ≤ 10E: ±200PPM/°C Temperature coefficient > 10E: ±100PPM/°C Resistance change rate is Short time overload ±5% (2.0% + 0.1Ω) maximum ±1% (1.0% + 0.1Ω) maximum Terminal bending ± (1.0% + 0.05Ω) maximum Dielectric withstanding ...

Page 4

... HP06 Series High Power Resistors Resistance Preferred Value Range E6 E12 E24 Above values in accordance with IEC Publication 63 (1963) and BS2488 E96 E6 E12 E24 10.0 10 10.5 10.7 11.0 11.3 24 11.5 11.8 12.1 12.4 12 13.0 13.3 13.7 14.0 30 14.3 14.7 15.0 15 15.8 16.2 16 ...

Page 5

... HP06 Series High Power Resistors Part Number Explanation: MC HP06 W2 Product Wattage Type Product Type : HP06 = 1206. Wattage : W2 = 1/2W. Tolerance : F = ±1%. : Where R = Ohms = Ω. Ohmic Value K = Kiloohms = KΩ Megaohms = MΩ. And replaces the decimal point. eg: 1R5 = 1.5Ω. 4K7 = 4.7KΩ. 6M8 = 6.8MΩ. ...

Page 6

... Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group's liability for death or personal injury resulting from its negligence. SPC Multicomp is the registered trademark of the Group. © Premier Farnell plc 2008. ...

Related keywords