TNPW0603150KDHEA Vishay, TNPW0603150KDHEA Datasheet - Page 7

• Manufacturer Part Number: TNPW0603150KDHEA
• Description: RESISTOR, THIN FILM, 150KOHM, 100mW, 0.5%
• Manufacturer: Vishay
• Series: TNPWr

Specifications of TNPW0603150KDHEA

• Resistance: 150kohm
• Resistance Tolerance: ± 0.5%
• Power Rating: 63mW
• Voltage Rating: 50V
• Resistor Element Material: Thin Film
• Temperature Coefficient: ± 50ppm/K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

TEST AND REQUIREMENTS
All tests are carried out in accordance with the following
specifications:
EN 60115-1, Generic specification (includes tests)
EN 140400, Sectional specification (includes schedule for
qualification approval)
EN 140401-801, Detail specification (includes schedule for
conformance inspection)
The following table contains only the most important tests.
For the full test schedule refer to the documents listed above.
The testing also covers most of the requirements specified
by EIA/IS-703 and JIS-C-5202. The tests are carried out in
accordance with IEC 60068 and under standard atmospheric
conditions in accordance with IEC 60068-1, 5.3. Climatic
category LCT/UCT/56 (rated temperature range: Lower
Document Number: 28758
Revision: 30-Sep-08
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1
CLAUSE
4.5
4.8.4.2
4.25.1
TEST METHOD
IEC 60068-2
-
-
-
Endurance at
Maximum pulse voltage U
Temperature
For technical questions, contact: [e-mail]
10 000 V
Resistance
coefficient
1000 V
TEST
70 °C
High Stability Thin Film Flat Chip Resistor
100 V
10 V
≤ 0.05 % (1000 h rated power at 70 °C)
10 µs
Conditions:
P
TNPW1206
TNPW0805
TNPW0603
i
≤ P
100 µs
whichever is the less severe;
Stability for product types:
i, max.
At 20/- 55/20 °C ± and
1.5 h on; 0.5 h off;
U =
PROCEDURE
70 °C; 1000 h
70 °C; 8000 h
20/125/20 °C
U = U
1 ms
P
70
max.
x R
TNPW0402
TNPW0603
TNPW0805
TNPW1206
TNPW1210
TNPW2010
TNPW2512
i, max.
10 ms
;
or
Category Temperature, Upper Category Temperature; damp
heat, long term, 56 days) is valid. Unless otherwise specified
the following values apply:
Temperature: 15 °C to 35 °C
Relative humidity: 45 % to 75 %
Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar).
The components are mounted for testing on boards in
accordance with EN 60115-1, 4.31 unless otherwise
specified. The parameters stated in the Test Procedures and
Requirements table are based on the required tests and
permitted limits of EN 140401-801. However, some
additional tests and a number of improvements against those
minimum requirements have been included.
100 ms
± 50 ppm/K; ± 25 ppm/K; ± 15 ppm/K; ± 10 ppm/K
Pulse Duration t
1 s
PERMISSIBLE CHANGE
± 1 %; ± 0.5 %; ± 0.1 %
10 s
± (0.05 % R + 0.01 Ω)
± (0.1 % R + 0.02 Ω)
i
REQUIREMENTS
TNPW e3
www.vishay.com
Vishay
7