NMTG-S12232BFYHSAY Microtips Technology, NMTG-S12232BFYHSAY Datasheet

Page 1

... Microtips 12F, No 31, Lane 169, Kang Ning St. Technology Hsi-Chih, Taipei Hsien, Taiwan, R.O.C. LCD MODULE SPECIFICATION FOR CUSTOMER’S APPROVAL CUSTOMER : NMTG-S12232BFYHSAY MODULE TYPE : APPROVED BY: (FOR CUSTOMER USE ONLY) Approved by 微 端 2006/11/8 張 秀 美 WEB : http://www.microtips.com.tw E-mail : Macros@microtips.com.tw ...

Page 2

CONTENTS ITEM FEATURES LCD MODULE DRAWING GENERAL SPECIFICATION ABSOLUTE MAXIMUN RATING ELECTRICAL CHARACTERISTICS OPTICAL CHARACTERISTICS MECHANICAL SPECIFICATION INTERFACE PIN ASSIGNMENT BLOCK DIAGRAM TIMING CHARACTERISTICS DISPLAY DADA RAM ADDRESSING DISPLAY COMMANDS COMMAND DESCRIPTION INITIALIZATION PROCEDURE RELIABILITY TEST APPEARANCE CHECK HANDLING PRECAUTIONS ...

Page 3

... DC-to- VERY CAREFUL ! The LCD driver ICs are made by CMOS process, which are very easy to be damaged by static charge, make sure the user is grounded when handling the LCM. SPECIFICATION FOR NMTG-S12232BFYHSAY 6 O’clock FSTN Positive STN Gray STN Yellow Green Reflective ...

Page 4

4 ...

Page 5

GENERAL SPECIFICATION Item Display Resolution Dimensional Outline(mm) Display mode Circuit Interface ABSOLUTE MAXIMUN RATING (1) Electrical Absolute Ratings Item Power Supply for Logic Power Supply for LCD Input Voltage Supply Current for LED backlight (2) Environmental Absolute Maximum Ratings Item ...

Page 6

ELECTRICAL CHARACTERISTICS Item Symbol Power Supply for Logic V IL Input Voltage V IH LCM Recommend LCD Module Driving Voltage I (LED DD Power Supply B/L OFF) Current for I (LED LCM ...

Page 7

... Dot Pitch Resolution Duty Ratio LCD Display Mode Rear Polarizer: Viewing Direction Backlight Controller DC/DC Converter EL Driver NMTG-S12232BFYHSAY 80.0(W)×36.0(H)×15.0 max(D) 0.42(W)mm×0.47(H)mm 0.44(W)mm×0.49(H)mm 122(W)×32(H) Dots Matrix 1/32 Duty STN Gray Mode Black & White(Normally White/Positive Image) FSTN Black & ...

Page 8

INTERFACE PIN ASSIGNMENT Pin No. Pin Out 1 V GND Logic supply voltage LCD driver supply voltage EE Display Data/Display commands switching input Ao=0: DB0~DB7 are command input and status output. Ao=1: ...

Page 9

Definition of Operation Voltage (Vop) Selected Wave Intensity 100 ％ Cr Max Vop [positive type] [Note 8] Definition of Response Time (Tr, Tf) Non-selected Selected Conition Conition Intensity 90％ 100％ Tr [positive type] Conditions: Operating Voltage : Vop ...

Page 10

Definition of viewing angle [Note 11] Description of Measuring Equipment 10 ...

Page 11

BLOCK DIAGRAM POWER SUPPLY 11 ...

Page 12

TIMING CHARACTERISTICS AC Characteristic—MPU Bus Read/Write I (80-Family MPU) Ta=0~50℃, V =5.0V±10％, unless state otherwise DD Parameter Symbol Address hold time Address setup time System cycle time Control pulse-width Data setup time Data hold time RD access time Output disable ...

Page 13

AC Characteristic—MPU Bus Read/Write II (68-Family MPU) Ta=0~50℃, V =5.0V±10％, unless state otherwise DD Parameter Symbol System cycle time Address setup time Address hold time Data setup time Data hold time Output disable time Access time Enable Read pulse-width Write ...

Page 14

DISPLAY DATA RAM ADDRESSING 14 ...

Page 15

DISPLAY COMMANDS Instruction Display ON/OFF 0 1 Display start line 0 1 Set page address 0 1 Set column 0 1 (segment) address Status Read 0 0 Write display ...

Page 16

COMMAND DESCRIPTION Display ON/OFF This command turns the display ON or OFF. D=1 : Display ON D=0 : Display OFF Display Start Line This command specifies the line address shown in page ...

Page 17

Set Column Address This command specifies a column address of the display data RAM. When the display data RAM is accessed by the MPU continuously, the column address in increased by 1 every time. Therefore the MPU can access to ...

Page 18

Read Display Data read an 8-bit data from the data I/O latch, updates the contents of the I/O latch with display data from the display data RAM location specified by the contents ...

Page 19

Read-Modify-Write This command defeats column address register auto-increment after reading data. The current contents of the column address register are saved. This mode remains active until an command is received ...

Page 20

INITIALIZATION PROCEDURE Detects a rising edge or falling edge of an RES input and initializes the MPU during power-on. Initialization status: 1. Display is OFF 2. Display start line register is set to line 1 3. Static drive is turn ...

Page 21

RELIABILITY TEST No Item 1 High Temp. Operation 2 High Temp. Storage 3 Low Temp. Operation 4 Low Temp. Storage 5 High Temp./Humid Storage 6 Thermal Shock Vibration Test 7 ( IEC-68-2-6 ) Shock 8 ( IEC 68-2-27) APPEARANCE CHECK ...

Page 22

HANDLING PRECAUTIONS (1) Treat polarizer very carefully since it is easy to be damaged. (2) When cleaning the display surface, use soft cloth (e.g. gauss) with a solvent (recommended below) and wipe lightly. ◆ ethyl alcohol ◆ iso-prcolol Do not ...

Page 23

LCD PRODUCT QUALITY STANDARD DISPLAY APPEARANCE No Item inclusions (black spot, 1 white spot, dust) 2 scratch 3 dent 4 bubble 5 pin hole 6 dot defect 7 contrast irregularity(spot) 8 dot width 9 color tone and uniformity obvious uneven ...

Page 24

REVISION HISTORY Revision Content The LCD module is compliant with RoHS Page 3-23 24 Date 2006/11/8 ...