MAX16841ASA+T Maxim Integrated Products, MAX16841ASA+T Datasheet - Page 10

• Manufacturer Part Number: MAX16841ASA+T
• Description: LED Drivers Wide Input Offline LED Driver with Dim
• Manufacturer: Maxim Integrated Products

The average current in resistor R16 is the average input
current of the buck converter.
If P
I
switch current occurs at the peak level of the highest
input voltage.
V
For optimum efficiency, inductor L5 must be operated in
continuous-conduction mode.
The current in the inductor would be at its maximum level
at peak of the highest input voltage. LED string voltage
is assumed constant. Calculate the duty cycle at peak of
the highest input voltage.
The percentage peak-to-peak ripple is considered
between 30% and 60% of the inductor current. Assuming
60% peak-to-peak inductor current ripple, the maximum
inductor current is given by:
The minimum value of the inductor is given by:
LP
CS
OUT
is the switch peak current. Maximum peak in the
is 2.2V. Allow 80% margin for tolerances.
is the output power, then the input power is given by:
Controller IC for Dimmable Offline LED Lamps
Lmin
I
=
���������������������������������������������������������������� Maxim Integrated Products 10
R16
LP
=
R
(
I
V
D
Lmax
=
CS
M
2 V
=
I
=
P
I
IN
IN
0.6 I
IN
×
I
IN
=
=
+
2 V
=
=
V
INmax
2 V
×
×
P
0.5
2 V
×
V
CS
P
2 V
P
R20 0.1V
IN
×
10µA
LED
OUT
Lmax
×
OUT
×
IL
INmax
η
× ∆
×
× π
INrms
P
M
Resistors R16 and R20
LED
+
80%
−
Inductor Selection
I
× π
Lmax
V
×
LED
f
SW
)
×
D
Figure 2 shows a PFC triac, dimmable, isolated (flyback
topology) offline LED driver.
Here the current through the Q4 MOSFET is controlled.
Current through Q4 is the same as the input current
of the flyback converter. The input-side circuitry is the
same as in the nonisolated buck LED driver that was
previously described. During startup, the device is
powered up from Q2, R10, R11, and D8. Bootstrap from
the bias winding on the transformer turns off the Q2
MOSFET, thus saving power from high-voltage line. Here
the switching threshold programmed by R15, R16, and
R18 can be lower than the LED string voltage.
Output-side electrolytic capacitors C8 and C9 are used
for filtering the double-line frequency current ripple in
LED current.
During an open LED condition, the voltage across the
output capacitors increases and is reflected on the bias-
winding side.
Once the bias-winding voltage goes above 22.5V (typ),
NDRV is disabled and the Q4 MOSFET turns off.
Choose the transformer turns ratio based on the voltage
rating of the MOSFET. Use the following expression to
calculate primary-secondary turns ratio:
where:
Factor 0.8 is taken into account for the voltage spikes,
due to transformer-leakage inductance.
Use the following equation to calculate bias-secondary
turns ratio:
where N
the bias voltage for the device.
N
V
V
V
DSmax
INmax
LEDmax
PS
is the primary-secondary turns ratio
AS
is the maximum peak input voltage
is the voltage rating of the Q4 MOSFET
is the maximum voltage of the LED string
is the bias-secondary turns ratio and 18V is
N
PS
=
N
0.8 V
AS
×
=
DSmax
V
V
LEDmax
LEDmax
18V
MAX16841
−
V
INmax